I'm using the nRF Connect SDK on nrf5340dk and encountering issues when trying to use the non-blocking (asynchronous) I2C API.
i am particularly getting this error - ENOSYS...
Hello everyone
I'm currently trying to make dynamic endpoints on my matter device. I changed the .zap file to accomodate all the possible endpoints (16) with clusters...
Hi community,
I have a similar custom board as Thingy53, which has the nrf21540 module on board.
my purpose is to turn on the nrf21540 and do the reconnection, when...
Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
Hi,
I use the nRF54L15-DK flash fimware (.hex) with "nRF Connect for Desktop - Programmer" success.
And I view the schematic, discovered the DK board have flash memory...
I have a NRF9160 design with a TPS63031 regulator providing 3.3v. When my battery gets weak I am seeing spontaneous reboots, likely due to input voltage droop.
I'm experimenting...
I am seeing excessive current in System ON, Idle mode. I am using WFI(). I have verified that
operation is being held at that instruction by using GPIO pin. Idle mode is...
Our manufacturer received new nRF51822QFAAH0 parts. Previously, we were supplied nRF51822QFG2 parts.
According to your PCN_092-1.2 Final.pdf document, there has been a...
Hi,
I can start MCP without the dongle PCA10031 (which I have updated the firmware on) and it starts ok, but when I then plug in and select the device COM 5 - 6xxxxxxxxx...
I would like to ask how to make advertisements which are less than one second. In my application, i need to scan for devices, when i find my specific device, i start to advertise...
I'm trying to programmate a simple blinkind led project to a custom board with a nRF51822 I did. I'm using a stm32 discovery to connect the custom board throw the SWD port...
I'm trying to update my beacon to use 8.0.0 SoftDevice 110. I've downloaded the 8.0.0 precompiled softdevice hex and loaded the Keil dfu_dual_bank_ble_s110_pca10028 project...
Hello,
I'm trying to use the APP_TIMER API to have tempo, but I've noticed a problem of accuracy when using the RTC1.
I use 0 as prescaler, so the RTC1 runs at 32768Hz...
Hello,
My question based on case, I've experienced recently.
nRF device that could advertise in general mode for limited time by pressing on button and continuously in...
Hello. I am having trouble setting up two PWM channels on nrf51822. The device is running S110 and SDK9.0.
The PWM initialization sequence looks almost identical to the...
Hi,
With reference to This link , I'm trying to make a Nordic solution which can support all beacon applications (iBeacon, Eddystone & Altbeacon).
I'm able to integrate...
Hello I am trying to program this nrf51822 module. I am using J link Cortex M9 . I want burn multilink peripheral in it.
I have followed this link.
I have connected everything...
I would like my device to advertise for 10s and then begin advertising again only on an external interrupt.
What steps are required to restart advertising without restarting...
I am trying to reprogram a usb dongle device from AdaFruit (Bluefruit LE Sniffer), which uses the nrF51822 SoC, using nrFGo Studio. In the device manager I'm innRF5x Bootloader...
