I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
I have a Nordic micro-controller nRF51 with 128kb of flash memory, I compiled with Keil, I generated a a program with:
Program Size: Code=23856 RO-data=632 RW-data=308...
I want to enable Notifications in my Central for a particular characteristic advertised by my Peripheral. There's example code that is supposed to do this in the BLE Central...
Hello,
i have a question about the use of the dc/dc converter in use with the softdevice S310 v3.0.
We make some difficult calculations and so the sensor its on for 750ms...
hi
as we know,ANCS need to pair,we have app for ios,iphone will pair with our devcie when i connect my device by my app,so iphone will connect my device when user open...
hi
my customer want to add DFU funcation to their APP(ios and android),i give them nrf toolbox source code ,i hope they can separate DFU funcation from that source code...
In my application I have to advertise and scan, I know these two actions are multiplexed and there are no problems when there is no BLE connection (I use s130, sdk 9.0.0)...
Hi all,
I'm developing little project on nrf51 dongle(pca10031). After few succeses now I have big failure which stops my work.
How my environment looks like: Ubuntu...
I built the GCC bootloader from source based on the suggestion of another user in this forum instead of using a precompiled hex file. The Softdevice is 7.1.
It shows DfuTarg...
I have a min connection interval of 200ms and max of 250ms. I have set slave latency to 10. These parameters are set both on peripheral and on central. Still, after connecting...
Hi! I am working on a project that uses the Multilink example. On the client (nRF51422 w. SD 120) my program crashes and starts the main loop again after a few seconds. I...
Hi,
I'm developing a device that will be powered by two AAA alkaline batteries.
Since the operating voltage of nRF51822 is 1.8 to 3.6V I was considering to connect them...
Hi,
the example ble_app_uart_s132 from the SDK 0.9.2 is not longer working with the new release of S132 ( s132_nrf52_2.0.0-7.alpha). I had to go back to s132_nrf52_1.0...
My setups are:
RBL BLE Nano
nRF51_SDK_9.0.0_2e23562
Keil uVision V4.74.0.22 or gcc-arm-none-eabi-4_8-2014q2-20140609-win32
My design is to advertise a manufacturer...
I'm using nRF51422 with SDK 9.0.0 and S310 ver 3.0.0.
First, I program softdevice and dual bank bootloader by nRFgoStudio. After that it is possible to program my application...