Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
hi
i have NRF51422-QFAA-R V2 ;
i want to know how connect reset pin of my jlink to it?
u see in pic that reset pin is on the swdio;
and also i want use a button to...
Hi,
I am working on the ble_connectivity example in nRF51_SDK_8.1.0_b6ed55f. A make error occurs when building this example.
Would you please tell me how can I fix...
If I understand correctly, a peripheral can distribute data such as UUID, device name, flags, appearance etc. between advertisement and scan response packets. To gather all...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
I am having problems programming PCA10028 using nRFgo Studio.
Note I am using SDK V10.0.0 and IAR EWARM 7.5
Program SoftDevice with s110_nrf51_8.0.0_softdevice.hex ...
My platform is uVision V5.15, running s132 SDK ble_peripheral examples on nRF52 DK.
When compiling the system_nrf52.c in these examples, the error message was shown:
...
Hello everyone, I have an application that i would like to complete and I have most of it finished on Arduino but there are size constraints. Because of that i found the Nordic...
hi, what's the function of the code *(uint32_t *)0x40008C0C = 1 in GPIOTE example of SDK 9.0,
and i know the address of 0x40008000 is TIMER0, and i check the another timer...
Hello,
I a developing a custom application on a custom board with nRF51822 and SDK 10.0. I am also a newbie with BLE, so please bear with me.
I have succeeded in incorporating...
Hello everyone,
I would like to make the following application.
I want to connect a temperature sensor to nRF51822-beacon to broadcast the temperature measurements
...
Hi,
What does the "Enable services" button in the MCP do?
What are the Master Emulator API equivalent command to duplicate the "Enable services" button in the MCP?
...
Two questions:
If I use Nordic's library functions such as app_timer_create() and app_timer_start(), are the timers using the low-power RTC timer running with the...
After I connected a BLE device (HRM sample program on dev kit), I call sd_ble_gap_rssi_start to do a RSSI measurement, it returns error code 6.
Apparently error code 6...
Hi,
I've encountered a problem during development of an application based on ble_app_hrs_rscs_relay.
Everything works fine (I mean concurrent central and peripheral...
