Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hello, I am asking for your help again.
I just managed to brick the chip that I am working with. The problem is that I am not able to erase or program the flash. However...
Hello,
I have not found a lot of information on connection encryption. I want to use a preprogrammed Long Term Key in my mesh that is then used to establish subsequent...
This is the application file I am trying to download:
dx02.zip
This is the sniffer Log I just captured by wireshark
dx02_20150820.pcapng
I was able to upgrade firmware...
We have a heavy duty scan based application being built on top of the nRF51822 SOC. We have tested the scan function (S130 SD) on both a custom PCB and also the Nordic Smart...
Hi,
I have PCA10028 board, and I'm trying to implement UART send/receive.
I've searched for the problem here but could not find a solution for it.
My uart init function...
Hi
I'm using Keil V5 to program the Nordic nRF51 DK ( the one here: www.nordicsemi.com/.../nRF51-DK) but I'm a bit confused as to whether or not I need to change the settings...
I am not quite certain what the advantages/disadvantages are of using LDV vs DCDC if you are using an external regulator. In my case i use a LiPo battery outputting ~4.2V...
In the ant-to-ble bridge example in the 7.x.x SDK, there is the following comment in examples/multiprotocol/experimental_ble_ant_app_hrm/main.c :
// Need to close the ANT...
Hi all,
As I know in constant latency mode, both the regulators (1v7 & 1v2) and HFCLK are kept on. Is there a way to keep the HFCLK on while one or both the regulators...
Follow up this image. I want to reduce the negotiation time.
10:44:43.655 --> Connected to D6:9E...
10:44:45.123 --> Services Discovered
= 45.123 - 43.655 = 1.468...
when i test the ancs example application for nrf51822, i foud a question : after i disconnect the lightblue ios app with nrf51822 peripheral, the iphone still connected with...
I downloaded ble_app_lbs from GitHub. Loaded the project (on GitHub it was saved as a MicroVision 4 project) into MicroVision 5 and build with no errors or warnings.
I...
Hi sir
I want to combine heart rate, proximity and uart(proprietary) projects to one project.
As your experience, is it possible? Any side effect for that? Thanks.
J...
I have an NRF51 board running as a GATT server. Using an iOS application (LightBlue) I connect to the NRF51. If I quit the iOS application then I get a disconnect event and...
