Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi all,
I have ublox nina modules including your nrf52833 .
I downaloaded the ublox application here:
Release C209 AoA Tag v2.0.1 · u-blox/c209-aoa-tag
and opened...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
Dear Staff,
we have some Ublox C2909 TAG based on your nRF52833 chip.We need to program them for an RTLS project.
In particular we need to:
customize the FW here ...
Hello,
I managed to run the examples for nrf54l15 channel_sounding_ras_initiator.c and reflector on my custom hardware boards. I changed the overlay files to use my own...
This is what happens when linking my project in Eclipse:
make all
'Building target: project_name.elf'
'Invoking: Cross ARM C Linker'
arm-none-eabi-gcc -mcpu=cortex...
Hello,
We would like our app to only be seen by:
Devices that have previously connected
Devices that we allow to be added to the whitelist via the temporary disabling...
In my pursuit to make a stable Gazell streaming device, I noticed some issues with pushing packets to the Tx FIFO.
Even through I get an affirmative response from the nrf_gzll_ok_to_add_packet_to_tx_fifo...
Hello,
After I connect my iPhone with a 8001 nordic chip without opening the characteristic I receive a pipe status event which says that the pipe is opened. This is totally...
Hi,
I would like to use the softdevice s130 because i want to try having a nrf58122 as a ble central and peripheral at the same time.
At the moment, there is still the...
Hey everyone,
I have an application where I have to write data to a characteristic. I would like to only allow reliable writes (not unacknowledged ones). Is this permitted...
Hello,
I'm having problems with defining RGB led on my beacon (pca20006). When i define for example RED led (on pin 12) with code nrf_gpio_cfg_output(12); i should be able...
Hello,
I am trying to load ble_app_beacon code provided in nordic sdk to redbear lab's ble nano. I am using sdk version 8.0.0 and soft device(s110) version 6.2.1 .
I am...
If BLE device is sleeping,is link layer connection terminated or the link layer connection is still valid..?
if it is valid..how the master will know about the sleeping periods...
Hi all.
Consumption current increases by about 1.5 mA after a battery check.
uint8_t battery_start(void)
{
// Configure ADC
NRF_ADC->INTENSET = ADC_INTENSET_END_Msk;...
Hi all!
My project is depend on the "ble_app_template",which uses the "scheld structure", I am able to read the data from app but not able to send my data with notification...
I have a question about that code, when I test my code with lightblue, it showed me that there is an service called application notification client service, but it didn't...
I'm using GPIOTE library to check the change of two switch inputs.
Normally it works well, but rarely GPIOTE_IRQHandler become never happen even if the pin level changes...
