I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
The BT SIG has adopted the "Indoor Positioning Service" and in there it says ...
"When a characteristic value is written, the Server may check the validity of the value...
Hi,
I need to send an audio signal through BLE connection of nRF51822 module, this signal need to quantized and sampled at rate of minimum 8000 sample/second by ADC, i...
I would like a working example of a simple application that uses soft_device (either S110 or S120) plus UART debugging.
I have read many posts in this forum about this topic...
Hi folks,
do you supply a BT Test-SW to set a module with your NRF51822 in different test modes like continuous FH etc. or to change the device to low, mid, high channel...
Hi,
I want to establish a peer-to-peer communication network between 2 nRF51422, such that both the nRF51422 can Transmit as well as Receive data. Is it possible to achieve...
hi,
as we know, the device need to being linked in 1.28s if Advertising types is BLE_GAP_ADV_TYPE_ADV_DIRECT_IND ,but my host can't link device in 1.28s,so i want to link...
Hi,
I try to evaluate DFU using serial but found difficulty. Seeking help here.
I use PCA10028. First, i falsh S110, v8.0 into it.
Then, compile SDK8.0.0\examples...
Hi all!
I want to allow only 1 device to bond at a time. If another device bonding, I want to delete the previously bonded one.
I tried to use dm_device_delete_all() in...
Hi all,
I'm trying to get TWI working on the nRF51 DK but it's not working.
I used the twi_hw_master_sd.c file so softdevice use should not be a problem.
When I debug...
I am using internal ADC to sample 2 (sometimes 3) channels on about 333Hz frequency.
What I do is:
set channel 1 as input (always two-thirds prescaling, VBG reference...
Hi,
I want to debug nrf51822 beacon using DK.I made the necessary connections between dk and beacon.I managed to flash the beacon using nrfgoStudio , but if I want to do...
I have the following code, it's pretty bare in terms of its functionality:
#include <stdint.h>
extern "C"
{
#include "nrf_delay.h"
}
#include "gazell.h"
#include...
I succeeded to made the BLE DFU example of SDK 8(bootloader\pca10028\dual_bank_ble_s110) with softDevice 8 working on PCA10001.
Now I want to try DFU over UART.
I follow...
Hi,
Sorry if these are silly questions but I've tried some searchings and still cannot figure out the answers for the questions below
What is GATT Server Context...
