Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi Team,
I was trying to load firmware to external board using nRF51-DK.
I have successfully programmed the boards many times and now when I am trying, LED (LD5) on nRF...
Hi all,
I downloaded the nrf51SDK_.8.0.0 from nordic site and tried to flash the new softdevice s110 but failed. I used an android application to flash it over the air...
Hi:
i use ble_app_uart project and want to change the UUID lenth(128 bit) to be 32 bit;but i change "nus_base_uuid" to be 4 byte and change "uuid128[16]" to be "uuid128[4...
Hi,
Does hardware that has already a Qualified design Listing (Bluetooth.org) requires re-testing of the RF-PHY ?
(refering to transmitter tests (i.e TRM-LE/CA/01/C (output...
Hi,
Im using a module NRF24L01 + LNA bought off ebay, connected it to msp430 via SPI interface. All spi communications are going solid, I manage to completely configure module...
I am trying to create a file and write to it during runtime. When I use fopen with "w" option to create a new file, the file pointer is always retuned to be NULL.
Is there...
Hi,
I recently tried SDK7.2 on PCA10028 board in order to make sure that SDK7.2 works well before I migrate my project to SDK7.2 codebase. My project code didn't work as...
Is it possible to do OTA from one nRF51822 to another? Is so how, and is not why?
I am using S120 and S130 for my applications and would like one device to uppgrade another...
Nordic has provided a good SPP implementation over BLE.
devzone.nordicsemi.com/.../
However, will it raise power consumption and cause BLE to lose its low-power characteristics...
When trying to do a direct advertise massage ( sd_ble_gap_adv_start ) I get error code NRF_ERROR_INVALID_STATE (Invalid state, operation disallowed in this state). This is...
Hi Team,
In my application UART is used.
I need to send parity bit based on particular responses that I need to send to the device
connected to UART.
Can I change configuration...
Hello,
I'm working with timeslot API (basing on github.com/.../observer) . I have an advertising and active scanning running concurrently. However, I want to completly...
I am using nRF51822 to generate 3K HZ PWM signal for a buzzer.
I read other people's question and try it.But as far i can't solve this issue.Please help.
At first i use...
Hello,
I just ordered a shiny new nRF Beacon from Mouser. The beacon is version 1.1.0 advertising "DfuTarg", so I am attempting to flash the application file that comes...
