I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
I am trying to communicate between nrf51822 and Android device using Gatt. But nrf51822 invokes UartService.ACTION_GATT_DISCONNECTED after some time, the disconnection happens...
Hi,
until today we develop our application on Nordic DK with nRF1422 with 32 KB of RAM.
We are using S130 and SDK 8.1.0.
Today we saw that our target module, the MBH7BLZ07...
Hi!
I'm working with nRF51DK with s110 soft device on it. I'm trying to write simple custom service which reads some data from sensors and send it over BLE to Android app...
Hello,
I know the current limit of 15mA to share among all gpio pins.
If I source/sink current in very short bursts (100ns every 1ms) can I draw larger currents than 15...
Dear All,
We are working on a custom board with NRF51822.Everything works fine apart from the timer. What we are doing is that once the board is booted, it reads some values...
Situation:
We are building BLE device that have GATT service showing a analog sensor value.
AIN2 is connected to the sensor. AIN4 is connected to battery.
We would like...
Hi.
I use nrf51822 rev.3 build number CEAAE00(0x0079) package is WLCSP.
Before I got a experience already develop wearable device using rev.1 chip. And that board work...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
I was wondering if the Master Emulator API requires the Segger IC on the nRF51 Dongle (PCA10031) to work? Or is this just used for programming the nrf-device via USB?
The...
Hi.
I'm using latest version of nrf51-pwm-library to test if PWM works fine, but unfortunately, it's not. I have very simple program which should fade LED from 255 to 0...
Is there an application note or specification that defines the term flash memory endurance and flash memory retention?
What failure modes can be expected when these specs...
Hi.
I faced very weird problem.
below is my structure of custom array;
if I set MAX_MYARRAYCOUNT as 20, it's OK.
but if I set MAX_MYARRAYCOUNT as over 30, device crushed...
