hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hello everyone,
i am trying to compile the Ble-UART_example but everytime it shows this error 'GPIOTE_config_irq_priority is undefined ) and i dont know what went wrong...
I have tried to flash my application targeting nRF51822 on our board by using a Segger on nRF51 DK. However, Keil compiler always shows that it couldn't find any nRF51822...
Hi NORDIC
I have to complete a function that one can transmit and the other can receive . but I do not know how to set nrf51822 to be a receiver . please tell me or share...
Hi,
it seems that the default implementation of the ble_bas (battery service) provides the notification feature but not the "read" feature.
I client can enable notification...
I'm using the Github project github.com/.../nRF51-multi-role-conn-observer-advertiser in order to SCAN in a specific channel rather than all 3 channels. In this example, softdevice_handler...
Dear all,
Recently,i use nrf51422 trying to receive data from two ant sensor.
i assign two ant rx channels at the same time, i find i can't receive data if only one sensor...
We are planning to use a synchronous independent channel, that senses whether there are any slaves or not using acknowledged data type.
More than one slave could have paired...
HI,everyone!
I want to use pstorage to store some data, so I followed the steps given by devzone.nordicsemi.com/.../ , but it didn't work.
Then I checked ecah function...
Hi all,
I want to test power consumption of data packets reading from SPI to RAM using PPI.
But i'm not sure that can RAM act as a peripheral of PPI...
So, can i use...
I am using a solar powered energy harvested circuit to power the nrf51 module. However, when the generated voltage drops below 1.8v, the nrf51422 enters into brown out reset...
Hi,
Now as I want to ensure low power mode with minimum hardware and firmware, I have written very small code to check it. Simply, I have initialized timer only and go...
I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
Hello,
In what code structures (from SDK) the storing bond information for the Android and iOs devices (random static or public addresses and private resolvable addresses...
Based on Battery Service I have made my own Service and Characteristics but I have problem with setting Indication. This is how my characteristic add function looks like:...
I am trying to build a project where I need to implement a button characteristic on a nrf51822 master device. I'm using S120 v1.0.1, SDK 6.1.0 and compiling with keil.
keil...
