We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
I want to implement the OTA update in nRF51822 on my custom board. I am using the bootloader example in the dfu folder for this. When I try this code on the DK, it works fine...
I am using nrf51822 with PCA 10001, SoftDevice S110 8.0.1. I try to compile the example "ble_app_proximity_s110_pca10028" and after I made a connection the device disconnects...
Has anybody had any experience in programming an nRF beacon kit over the air using the built-in Bluetooth Smart interface in a Windoze 8 laptop? (HP 255 G3) Is this even possible...
Hi,
I wanted to create fixed rate waveform. I first used nrf_delay_us with nrf_gpio_pin_toggle. But I realized it is not accurate enough to do it, especially when the device...
Hello,
I'd like to know how exactly do i implement this function in my app?
I tried getting the value from response (as shown in documentation) : ble_gattc_evt_char_val_by_uuid_read_rsp_t...
Hi,
My Jlink lite CortexM work with nrf51822 DK boards. But my PCB with nrf51822_xxAA chip can't download code. I'm using ukeil
When I chek in utilities Jlink can't recognize...
I am initializing an SPI master to talk to ADXL362 accelerometer using NRF51-DK.
Datasheet page 19: www.analog.com/.../ADXL362.pdf
No matter what I do connected or disconnected...
Hello,
I am new to working with imbedded chips and could use some help. I am working with a pre-programed nRF51822 chip on a PCB and would like to be able to read the imbedded...
Hi I want to using nRF51822 link with MCU ti-am335x have Linux system(Ubuntu) by standard HCI command, BlueZ or related hci tool.
I know that I can use nRF51822 S120 serialization...
I would like to share my wireshark capture file (pcapng) with another developer to view that doesn't have a nordic sniffer. They cannot see the ble protocol information. Is...
I am able to set the connection timeout to 250ms in the ble_app_hrs peripheral sample, but in the ble_app_multilink_peripheral it will not advertise if I set it below 1000ms...
Hello,
When using the bootloader I've noticed that the booatloder resets after advertising for ~1minute. I'm try to figure out if this is intentional.
I notice that...
Hello,
I am currently designing a project that will advertise as two different beacons simultaneously using the Timeslot API. I have successfully implemented the nRF51...
In my all projects, I am using this code to obtain and set local device address:
uint64_t deviceId = ((uint64_t)NRF_FICR->DEVICEID[1] << 32) | ((uint64_t)NRF_FICR->DEVICEID...
