I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi,
Here is output of my chip and i want to read it but there is a problem 25 uS low width (T) is to quick for nRF51822
Can you give me some tips, how to read this 3 signal...
Hello all,
I notice that this library isn't listed in the "SDK Common Libraries" for S210 - is it ok to use this? Internally it does seem to be ANT-aware, even though softdevice_handler_init...
Hi everyone,
I'm using NRF51822 controller for an application, to store 2 float variables in the memory using persistent storage manager feature.
However, when I try...
Hi All,
I try to implement the DFU funtion in my module, but the message return is “Not Supported”.
Please suggest me, how could I do about it?
Thanks.
Vic
...
Hello,
Is there a restriction that I cannot have same address LSByte for radio pipes?
It seems that i am failing to receive data on pipe 0 if for example I have pipe 0...
Hi:
I use SDK7.2.0 encountered a problem when I was disconnected, has reached the maximum number of bonding, I want to remove the first bonding information. I do not know...
when i use sd_ble_gatts_hvx() to send data,it cause a HardFault error。 when i trace the sd_ble_gatts_hvx() function,it will run to 0x00016432,in there will be compare two...
Hi,
I use sd_ble_gattc_write function to write to my peripheral with my central device. I'm sure the settings should be right but i still can't see any change on peripheral...
hi,
i have successfully entered the dfu mode many times and could change the applications and reenter the DFU mode.
But then i tried loading the softdevice at "nRF51_SDK_8...
Hi, All,
I am currently developing with nRF51822AC. Due to some issue, we would like to replace the current 16MHz crystal with a crystal other than this frequency. We would...
softdevice 8.01 s110
device nrf81522
hts example,add three ch adc,lcd eg.
phone : HTC one M7
app:nrf tools HTM
when try to connect the device by BLE, when recive the...
Hello!
I am trying to run example uart project (uart_pca10028) on PCA10028 development board. When code is loaded to the microcontroller it signalizes error - all leds...
Hello All,
I am working with a pre-programed PCB; the main components of the are a nRF51822 chip, a GPS, and a GSM. I am using a J-link to communicate to the entire board...
Hi,
I have a BLE thermometer I want to snif using nRF-Sniffer and Wireshark.
Unfortunately I'm unable to sniff the data, I only see the initial "hand-shake".
Process...
