Dear Technical Support Team,
I am trying to integrate and run TensorFlow Lite Micro on the nRF5340 Development Kit using the nRF Connect SDK. I have tested both SDK version...
Hi,
I am working with the NRF52832 SoC using the NRF52 DK and developing with NRF Connect SDK version 2.7.0. I have enabled BLE with LBS, BAS, and FUOTA services, along...
It is nRF54L15 + SDK 3.0 + Matter application.
I have developed a custom BLE service that is based on Nordic's proprietary NUS BLE service. The BLE custom service is enabled...
I am testing out the nRF54H20 on the nRF54H20-DK version 0.9.1. I have followed the steps for setup in the "Getting started with the nRF54H20 DK". I currently have nrf54h20_soc_binaries_v0...
I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
Hi. I want to disconect softdevice and ble in order to access to flash memory. I know there are a lot of ways to deal with it. But i want to test to disconect softdevice and...
Good afternoon, Today we had a question about the certification of our product related to the reliability of communication. We received a letter of the following content:...
Hi,
I am trying to update my advertisement data as well as scan response data (i want to put some custom advertisement data and the device name in scan response data). ...
My three buttons are pressed each time, and the LOG information is as follows
0> [00:00:00.000,000] <info> app_timer: RTC: initialized. 0> [00:00:00.000,000] <info> app...
SDK:15.3.0
CHIP:52832
I downloaded sdk15 for nrf52832.all sample programs and soft devices are working fine but boot loader coding is showing some error. I am using this...
Hello,
I am developing the following application:
An nRF52840 bluetooth module connected to a sensor does data acquisition and then sends it directly to an nRF52840...
Hi,
I am trying to use SPIM3 to drive LCD(ili9486), but I have encountered some problems, hoping to give me a solution.
I have 2 questions:
1. spi_config.dcx_pin
How...
Hello, we have run the power profiler on two different example projects, and want to understand the difference between the two.
When we run the blinky project
nRF5_SDK_16...
I am buys setting up a project on the NRF52 that needs to use the TWI. Usually I would read byte for byte, and if one of the registers has enough data to justify it, I would...
I tested sdk16.0 with secure uart debug example, that DFU needs to enter bootloader twice(press button4 and reset twice), first time to update setting file, second time to...
Hello,
I am developing using nrf51822 and J-Link.
In the Keil4 version, the RTT viewer worked fine, and only the project was migrated to the keil5 version,
but the RTT...
I'm using PCA10040 to test nRF52832.
But I can't see J-link device after connecting USB.
I installed J-link(segger), nRFgo studio, nrf command. But I can't see my PCA10040...
Hello, we are using the ble_app_uart example code, and are trying to modify it so that if a certain UART sequence is received from the connected microcontroller, it will disconnect...
Hi
I'm working on a project interfacing the nRF52840 board with the lis2dh12 accelerometer
I'm using SDK 15.3, basing my code on the provided driver and information...
Hello!
Now I have two devices about nrf52832 .One is central and another is peripheral. So I want to transfer the peripheral mac address to the central via nfc.
I do...