Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
good work.
I will have a question for you .
I think to make the connection and the connection I made adxl345 nrf51822 and LCD screen x, y and z coordinates , I want to show...
I use sdk 9.0.0, softdevice s130, nrf51422_xxac. In my application I have to both scan and advertise. When I start one of them (scanning or advertising) application starts...
Hello everybody,
I'm trying to use the RTC1 in the LedButtonDemo, in order to blink the led once we put 01 in with the Master Control Panel on my computer, but all my tempos...
Hi I need to test serialization with Nordic , since I need to use it for my application..
I want to first try it with my Linux Laptop. i.e, Connect NRF51822 to my PC using...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I just converted over from SDK8.0 to SDK8.1 to use the pwm library. After I was done, I figured out by searching on here that the GPIOTE is drawing ~1.1-1.2ma in sleep.
...
Hello everyone
i ahve configured the button and i want to make the function like this press the button for 3 sec and then the device should start advertising can anyone suggest...
We are running tests using the spi_master_with_spi_slave example and using an oscilloscope to see if we are getting any signal from the clock or the MOSI but we have not received...
I want to use mcp(master control panel) for windows to search for ble devices and do dfu via bluetooth, how can tell me how to set up the windows and usb dongle?
this is my sec_param:
sec_param_bond 1
sec_param_mitm 1
sec_param_io_capabilities ble_gap_io_display_only
sec_param_oob 0
sec_param_min_key_size 7
sec_param_max_key_size...
Our present application makes heavy use of the nrf51822 UART and I2C interfaces. We have a 115200 baud UART channel and thus need HW flow control. We are interfacing to an...
I would like to create wearable fitness based applications/hardware using nRF51822. But i am not sure how to get the fullest of power down modes in the chip.
For example...
Hi,
I purchased an nRF51 DK recently.Followed this tutorial to compile and flash an example project:
devzone.nordicsemi.com/.../
Here are the tools used:
Keil...
Hello，greetings.
I am trying to communicate among 2 NRF24L01+ modules using stm32 and stc89c52.
With EN_AA = 0x00, EN_RXADDR = 0x00, SETUP_RETR = 0x00 on PTX ,and EN_AA...
