hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Good day,
we would like to use a central and a few (4) peripherals. Peripherals would stream small chunks of data (few bytes) very frequently (10-50Hz). What are the drawbacks...
To reduce power, I'm trying to find the best approach to minimize the cpu load when sampling an accelerometer at a high rate, e.g. 1.6Khz. Is there a way to DMA a sensors...
I am writing a crc checker for the application and the softdevice . I am using a s120 version 2.0.0 it currently has a upper boundary of 0x1D000 is this a hard boundary for...
Hi everyone.
I am making an application which combines two services (ANCS and Nordic UART). I compare the advertising_init() function from the two provided examples (ble_app_ancs_c...
Hi,
I've been searching the devzone for TWI examples, and preferably an example with MPU6050. Here are a conclusion of stuff that I found, but as some of them were for...
Hi ,
I tried to upload the application firmware using OTA service through MCP, I successfully get connected and the transferring of application hex file also gets successfully...
Hi Guys,
once again, I have strange behavior of my code.
In my code I try in loop after ble_event received change PWM from 0 to 255 for my motor device. In debug logs...
Dear,
Please, could help me ?
My knowledge in RF is basic.
I am developing a system to use 8 RF channels (nRF24L01 +) simultaneously.
I'm using Balum 2450BM14A0002...
Hi,
I’ve just ordered a few nrf51822 (from seedstudio ) and waiting for them to arrive.
They come preloaded with SoftDevice 6.0 or 7.0. with a pre-flashed OTA boot loader...
Hello, I am trying to connect a Nexus 6p running Android 6.0 to the NRF52 dev board. I have tried numerous ble examples in the SDK, but nothing ever appears in the nRF Master...
So if I start a program in debug mode some zero-inited static variables are non-zero.
ldr r1, =__etext
ldr r2, =__data_start__
ldr r3, =__data_end__
subs r3, r2...
I'm attempting to use the app_trace module. I've set it up as follows:
int main(void)
{
// Setup tracing. Also sets up UART.
app_trace_init();
app_trace_log(...
Hello,
I know that this question has been asked a few times, but I am a little desperate after trying to get debug logging over the Virtual COM Port to work. Here are the...
Hi,
I've recently got some brand new nRF51 Dongle, and used nRF51 DK. The problem is that DK is not recognized by mine PC. There's actually some example program (heart...
