Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Howdy,
I just got my nRF51822 Bluetooth Smart Beacon Kit. I down loaded "nRF Beacon iOS_1.0.zip" and fixed up the project and targets so that it was using the correct Code...
Hi,
I have read the Bluetooth specification version 4.0 and found this figure
It discribled we could use OOB to disvocery and exchanged device information to connect...
Hi,
I am using nRF Loader built from its source code.
While it works well on iO7, does not work on iOS8.
After pressing an upload button in PROGRESS pain, the status...
I see from the 51822 PAN sheet v3.0 that item 61 still shows Rev 3 QFAA package devices as potentially having problems with LO leakage. We are in production with R2 QFAAG0...
Hi,
I am trying to run the ble_app_hrs_c, using:
s120_nrf51822_1.0.1
nrf51_sdk_v6_1_0_b2ec2e6
PCA10006 + nRF6310 + nRF6350
After the compilation of the...
I need to port ssd1306 library for oled to nrf51822.
so i tested following code. but it's not worked.
main(){
if (!twi_master_init())
{
return false;
}
ssd1306_init...
I am using the GCC DFU project provided by Nordic on GitHub ( devzone.nordicsemi.com/.../)
I altered the main.c to trigger to DFU mode based on the contents of the GPREGRET...
I'm trying to connect a camera module ( OV7670 ) to my nRF51822 EK. The camera requires an operating current of 18mA. If i were to connect the 3.3V rail input for the camera...
I have code that uses two GPIOs to program an NRF51822 via SWD mode. This code all works fine and suceeds in programming the device.
What I would like to do is get the...
How can I relocate or manage the transition between the bootloaders interrupt vector map and the applications interrupt vector map which will be at different addresses in...
Hi !
I'm completely new into programming this device.
I downloaded the nAn-36 source from Github and I'm trying to make it work on a PC10000 dongle.
The code stops in the...
Hi,
I wonder if there is any way to disable the Rx FIFO so that I don't have to fill it to generate an event, since I need exact timing for every incoming byte.
Also,...
