Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
I'm trying to understand how pstorage allocates storage.
PSTORAGE_FLASH_PAGE_SIZE is fixed, that's the actual size of a flash page and thus a basic unit as you can only...
Hi, I am trying to change the beacon data.
I changed Beacon UUID already, but I can not find where can I change device name.
I guess I need to change the gap_adv_data...
Hi,
I am upgrading to SDK 6.0.
What function should I use for retriving the whitelist data?
SDK 5.2:
//err_code = ble_bondmngr_whitelist_get(&whitelist);
//APP_ERROR_CHECK...
I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Hi,
How to implement the static PIN type pairing, when the server device doesn't have keyboard or display? Our requirement is, Master will initiate the pairing process and...
Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
Hello,
I am trying to implement a Time-On-Air measurement with two nRF24L01+.
I set up the devices to work at 2Mbps, 3 bytes address, 1 byte payload, 1 byte CRC.
Both works...
I'm using the nrf51822 evaluation kit. There is low level access (via memory registers) the the 2.4Ghz radio in either a Nordic proprietary protocl mode, or Bluetooth LE mode...
Hello Nordic Semi,
We are using the nRF24L01+ for a remote switch application. We have a small transmitter button (nRF24L01+ layout as per datasheet with micro controller...
I have a problem within the following szenario:
I transfer data from my nRF51822 Peripheral to a connected Central (Android App) as a bunch of Notifications with maximal...
my project can't goto sysoff mode, (desktop2)( project based on mouse demo)
m_prw_mgmt_set_sysoff_timeout(DEFAULT_BTLE_INACTIVITY_DISCONNECT_PERIOD);//can't sleep here...
DEFAULT_BTLE_INACTIVITY_DISCONNECT_PERIOD is 3600//one hour
i can't wakeup if disconnect'time over one hour.
but i can wake up form com_event_advertising_timeout
my code...
Hello,
i would like to know if the new SoftDevice 130 for the nrf51822 is compatible with the DFU OTA bootloader example provided in the SDK (nrf51822/Board/nrf6310/device_firmware_updates...
