Hello,
I want to try the XIP function on the nrf52840 DK, because we want to use this function later.
But i can not find any example of XIP on 52840. So i tried to modify...
Hello Nordic team,
Environment:
SDK 3.1.0
nRF54L15
UART / RS-232
I am seeing different UART TX timing depending on whether I transmit from inside the UART RX...
I’m working on a product that has been in the field and working for many years with nRF5 SDK v15.0.0 / softdevice 6.0.0. Now we want to add extended BLE advertisements and...
Hi everyone,
I am trying to add a bootloader for the NORUB126 board.
Before adding the bootloader, my application did not use any bootloader and everything worked correctly...
Hi there,
1. I want to sniff BLE LESC bonding session in tshark/CLI not in Wireshark/GUI. And decrypt it in the same session using LTK. The idea is to increase the time...
Hi, I need the nRF91 SiP SUPL client library (for A-GNSS via SUPL on my nRF9151, NCS v2.9.1). The official download process is not working for me, same problem many others...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
I'm just getting started with some Nordic development. This is on Linux (Ubuntu 12.04LTS) using nRF51 SDK 10.0 and gcc arm embedded toolchain. I have a PCA10031 and a PCA10000...
When I add a new directory to my project for some source files, I get the following error:
"Browse information of one or more files is not available"
If I move the source...
I am having an issue programming my nRF51 DK through IAR. I am able to compile and build the project, but it gives the following errors when I try to Download and Debug: ...
Hello,
I just got an rf51 dongle (usb) dev kit. I have installed the latest SDK, JLINK drivers, nrfgo studio. I copied the firmware .hex file into the JLINK drive as per...
Hi, I can't seem to pair my iPhone 6s or iPad Air (both v9.2) with demos (uart and temperature) running on my PCA10040. LED1 is flashing indicating that it is advertising...
I was under the impression that HomeKit was an extension of the MFi Accessory Interface Specification, which relies on the iAP protocol to access additional functionality...
Hi.
We are developing a test equipment for devices that use nRF905. The devices use single ended connection for 50 Ohms antenna and layout recommended by datasheet (nRF905...
Hi,
I am using ios app to connect nordic BLE module. I am getting continuous disconnection after 1 minute on app . Please let me know how to configure for continuous data...
HI:
I use my own nRF51822 board for a snifer(not PCA10000, PCA10001 and nrf51822 development dongle). Run ble-snifer-.exe, I could ger the information as figure 4 in ble...
currently i am using nrf52 as spi master with an imu as spi slave. based on the sdk code spi_master_with_slave, I write a sample test code to read the register value from...
Hello Nordic Community,,
Do I need the typical MBED hardware setup (Interface chip connected to 'target' (the nrf52)) in order to program the nrf52 with FOTA using an MBED...
Hi,
I'm using nrf51822. After sending a data from TXD, I enable the TXDRDY interrupt by setting INTENSET register. Then I can get into TXDRDY interrupt handler function....
Hello,
I found some posts discussed before.
I2C/TWI slave with nRF51822 [closed]
Using NRF51X22 as TWI Slave
In SD8.0, SDK10, does it still only support the TWI...
