But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
We're targetting the nRF51822 and use the pc-ble-driver (via connectivity_1.1.0_115k2_with_s130_2.0.1 )
Currently I'm using the dev board and the virtual COM port connection...
Hello,
I am trying to move from ARM Compiler v5.06 to v6.4, but I encounter an error, which I cannot handle.
The project builds fine with v5.06. When changing to v6...
Hi;
I am trying to secure DFU OTA. For that, i am using SDK12.2.0 and done with example file.
Now how to generate this .dat file itself.
Also explain each parameter...
I've been using a HC-05 (bluetooth v2.0) to communicate between my Unity-Android app and my Arduino microcontroller. It's working fine, however, if my prototype continues...
Dear all,
I have been working with a nRF51422 device for about two weeks, and everything went good.
This morning, out of nothing, i got this error in IAR: Warning: Stack...
Hi,
I have disabled the reset functionality of SW5 on nrf52840 PDK by giving the following command
" ./nrfjprog --recover -f" as it is mentioned in PDK document.
Now...
Hi Nordic devzone,
I'm wondering if you guys at Nordic are willing to release the source code for the mbed interface binary for the ATSAM3U2C. The current version of this...
Hello
I have a problem with my code implementing BLE NUS peripheral. Program hangs in the function sd_softdevice_enable. I have tried with external oscillator and with internal...
My previous product uses an empty notification to indicate that a bulk transfer is finished. I attempted to send an empty notification but got error code 0x10 (NRF_ERROR_INVALID_FLAGS...
I'm using the pstorage driver on the nRF51 to maintain several NVM variables. The NVM functions correctly and maintains state between power cycles. However, when I reflash...
Hello to all Nordic jedi masters!
I am using the nRF52832 along with SDK v11.0
I want to have the SAADC generate events only when the converted value is above a certain...
Hi all,
I am using a nRF52-DK board to receive data from the USB port using Serial, and transmitting it using ESB to a second board. If I use either Serial or ESB individually...
The latest rev of the product spec (1.1 when this was posted) includes a table on page 77 that indicates that the System OFF draw depends on a wakeup source (e.g. GPIO, NFC...
while i open ble sniffer , it sucessfully recognizes the nrf51822 ble nano but when i press w to open the wireshark, it shows no packets and in the interface list it shows...
