Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi,
I'm trying to implement some direct advertising, but I'm a little lost in the process.
Could you provide me with an example of code ? I read somewhere that ble_app_hid_mouse...
Hi,
I want to make RPI bluetooth //meshctl app works along with nRF Mesh App. Objective is to make Raspberry pi has non provisioned node, use nRF Mesh to add RPI has provisioned...
When I use the nRF Sniffer on a 52840 or 52832 with Wireshark I can see the RSSI values for each advertising message for all 3 channels (37, 38, 39). So for each advertising...
Hello I would like to use both UARTES in the exemple "ble_thread_dyn_mtd_coap_cli_pca10056_s140". I tried to adapt this example using the example "nRF5_SDK_for_Thread_and_Zigbee_v4...
I am using SDK 15.3, SES 4.3 and SD 130. I've added the saadc example code into my code which is comprised of the ble_central, nordic UART and saadc.
I've changed the timer...
Hi!
I just got the Thingy:91 to play around with, but the modem firmware is old. Is it possible to update the modem firmware using USB and the Programmer software? The ...
Hello,
I am trying to build a Zephyr application for the Thingy91 which uses the I2S module to receive audio data from an external microphone and sends this data via BLE...
Hello,
i would like to point out what i think is a missing dependency in file "include/modem/modem_info.h". At row 187 there is:
but at_param_type is not declared in...
I am going through the steps for building a secure bootloader
https://devzone.nordicsemi.com/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader
However I...
Hi,
I am trying to better understand the eSIM provisioning process. I want to verify that the IMSI changes to a local profile after the first registration with the provisioning...
Hi Nordic Devzone readers,
Recently I've picked up a NRF9160DK and have tried to program my own user program onto it. This will consistently fail unless I hold the reset...
Hi,
I am using the BMD340 module from Rigado. The module is connected to a raspberry compute module via UART. The design implemented is the “CLI co-processor design” where...
I have downloaded ADC example to the board nrf51422. I could not figure out how to give analog input and view digital output. please help. Thanks in advance...
To the kind attention of Nordic support team,
I'm using sdk 15.2, I'm working on usb hid composite example, and I modified it to have it scanning a big input keyboard matrix...
Hi,
As we know,we can modify the Mesh params though the config model, but when we actually installing and deploying ,If we want to improve the reliability of the Mesh network...
