Hi,
I am currently developing an nRF54L15 module.
During the evaluation, I measured the Tx current consumption and got a result that was 2mA higher than the value listed...
Hello,
I am working on custom hardware that is based on the nRF7002 DK. The following parts are presently listed as either EOL or NRND in distribution. L6, L8: Taiyo Yuden...
Hello,
we are testing the channel sounding performances for distance measurement with the example:
https://docs.nordicsemi.com/bundle/ncs-2.9.1/page/nrf/samples/bluetooth...
I am trying to connect some I2C sensors to the the nrf9151dk and I cannot figure it out. Where do I physically plug the sensor into the board and what configuration setting...
Hello, I am having issue to migrate a working project based on Azure IoT Hub Application code from 1.7.0 to 2.7.0, I have resolved all errors associated with changing the...
I'm running the peripheral_ancs_client using the 2.9.0 SDK on a nRF5340-DK. On an iPhone running iOS18, the device is not visible under Settings->Bluetooth when the nRF5340...
This feature used to be helpful pre version 2.7 or so, but has persisted as an issue since then. All of the configs in any *.conf are all underlined and have this phrase when...
Hi All,
I am designing a circuit with nrf51822 and mcp25625 (microchip spi can interface). mcp25625 has an internal 16mHz xtal clock circuit and a digital clock out, I...
Hi, i'm kinda a newbie on this, and i'm trying to port the SDK available for arduino to a PIC, i followed the instructions on the SDK and also here
Now i want to verify...
I ran into an issue recently of attempting to make a pstorage_update call from the callback set in pstorage_register . It resulted in a difficult to track down error, so I...
I have a USB dongle of nRF24LU1p and it is identified as the Basic Remote firmware with a VID:PID of 1519:002B. I would like to reprogram it over USB but do not know how to...
For nRF 51822 radio transmission, the payload packet is started at the NRF_RADIO->PACKETPTR. Then what is the packet size? is there any parameters to control the packet size...
I should have an own function wich is called upon after Port 3 goes low. I haven't succeeded yet using ppi channels. (I'm using the NRF51422)
For the moment the code is...
Hello folks ;
I'm new here and glad to have such kind people around to see helping those other developers ..
Here is my question
I'm using one of the NRF24L01 modules...
Hi,
I'm using the attached circuit and we recently took our product to FCC testing and failed the 2nd harmonic because we were transmitting too much power.
I'd like...
Hi All,
We have been working on Arduino Mega board with BLE shield. We want to get the address of the BLE shield and we are using aci library for that.
I found this...
I'm in the process of designing a consumer product using the nRF51822. I'm using the "square wave" antenna and matching circuit exactly as the are in the development kits...
Hello,
we are based in Germany and need a way to mass-programme the nrf51822 for production with our custom firmware+the softdevice.
Unfortunately we haven't found any...
Hi
I am writing an application that will have to switch the radio in between a number of different modes. (With/without AutoAck, and with/without dpl).
I have been looking...
Hello,
according to the documenation, the function sd_ant_burst_handler_request() can return with the error code NRF_ANT_ERROR_MESSAGE_SIZE_EXCEEDS_LIMIT. When will the...
Hi,
I was thinking if it is possible to use, per example HackRF greatscottgadgets.com/.../ , to tune the antena of the nRF15822 seeing if it is transmiting on the 2.4Ghz...
