I am new to this forum and have some questions that I could not find elsewhere. The questions are:
Website asks me for a product key if I try to download the S210 soft...
Hi,
I'm starting to implement DFU using IAR's ARM workbench. In the example project for ARM that comes with the nrf51_sdk_v5_2_0_39364 SDK there is a file called bootloader_util_arm...
Do I have to use external host MCU for nRF51422? What can the ARM Cortex processor inside SoC 51422 do and cannot do?
I want to create a mesh network with hundreds of ANT...
Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
Hi
S110 v7.0.0-2.alpha got released today.
In the release notes it says...
[b]The SoftDevice can now be configured to forward interrupts to one of several applications...
Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Hi,
I am searching for a way to disable then re-enable the BLE packet transmission on PTU.
This is for testing the A4WP conformance test PRU/PC/GR/Link.
"Disable the...
Hi,
I just got an Arduino and a BLE shield. I was following the Smart Starter Kit. The demo project have me errors, so I just started using the proximity example, and editing...
Hi,
I am using the nrf8001 module provided by adafruit ( www.adafruit.com/.../1697) but it's not clear if the RDY and REQ pins available on the chip are active low or not...
I have made a small device composed by
SD310-1.0, boootloader and application. The device is sealed to be waterproofed and has a serial conenction used by the custom bootloader...
I've been working with SDK 7.1 and I am struggling to understand how to get the makefile working with an NRF51822-QFAA device rather than a nRF51422-QFAC. I have samples of...
Hi all,
I did this upgrade hoping to have a TX_COMPLETE event issue fixed (I'm not able to send more than 1 buffer per connection it seems in my notification based service...
Hi,
There are two advertise nodes, only broadcast (one packet/s) . The S120 star scan. At the beginning everything is OK，but after a while, maybe 3-5 minutes, only one...
Dear all,
I've loaded this example github.com/.../Blinky_ble
into the nrf6310 as it is, and s110_nrf51822_7.0.0 as a softdevice
I am connecting to the module through...
I need the nRF51-DK-HW hardware files ，but without a product key.
And I cann't buy a nRF51 in CHINA.
Someone can give me a product key or
help me to buy a nRF51.
Thanks...
Hello everyone,
I have developed a firmware that makes accurate time of flight measurements, working with my own protocol.
Now I need to integrate this firmware with BLE...
Hi,
We would like to switch to a stand alone debugger for nRF51822, However in the product specs ( www.nordicsemi.com/.../nRF51822 ) mentioning that standalone programmer...
Hi guys,
I have nRF51822 Evaluation Kit.
I am trying to make simple project for my senior design.
Here is the setup.
I need to control simple on/off switch from...
Hi, I'm developing a BLE application.
I want to send multiple packets (from same characteristic) per connection interval.
I've read this question:
devzone.nordicsemi...
hello,
I am trying to develop an application using s130 softdevice on NRF51822 board.
i am able to do a undirected adverisement after a scanning. But when i am trying...
Hi
I use proprietary service to transmit data between iOS and nRF51822. The example I referred to is below.
C:\Keil\ARM\Device\Nordic\nrf51822_v6.0.0.43681_Backup\Board...
