Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
When I try to read data from UART RX port using serial library, I'm not able to read the data beyond the number specified by
SERIAL_FIFO_TX_SIZE and SERIAL_FIFO_TX_SIZE...
Hey, I'm using raspberry pi 3 model b, with the rasbian strech os running in it. I have followed the tutorial provided by nordic using this link for BLE over IPv6. When I...
Hello, In my case, i'm using some PTX and one PRX. It's working well. Now i want to extend coverage, can i use repeater/forwarder? I tried but have problem with PTX: after...
Hi,
we are using a custom board, with codes tested on a NRF52 DK. We reconfigured the pins and when using pin P0.09 (by default NFC) as an input "active_high" and with ...
Hello,
I've done this steps:
I erased the whole chip: nRFgo Studio/ DeviceManager/nRF5x Programming/Erase all
I programmed the Softdevice s132_nrf52_5.0.0_softdevice...
Hello Nordic Team,
i use SDK 12.3 and SoftDevice S130.
In the template project ( \examples\ble_peripheral\ble_app_template ), the BSP module is used to indicate advertising...
Hello,
For my project I need to send raw data (without prefix or timestamps ) along with system logs trough the same UART.
So far one possible solution is to use NRF_LOG_RAW_INFO...
I've been using nRF24LE1 for development. The HAL library provide the AES encryption for ECB mode. Now I need the decryption function. Does anyone has the realization? Any...
Hello everyone,
I use SDK14.2 and s132 softdevice. I can read "NRF_SAADC_INPUT_AIN0" and "NRF_SAADC_INPUT_VDD" pins and system is working properly.
Working Code like...
Dear friends,
I am using the nRF 52832, s132. I want to know the BER (bit error rate) of the BLE link. How can i measure it? Further, to what extent do other radio interferences...
Hi.
I want to know the time difference between functions by using a timer instead of a difference. I've looked at app_timer.h, but it's hard to understand.
I do not need...
I am trying to use the ADC to take power measurements on an interval. I found an example to read the values out online:
void ADC_IRQHandler() { nrf_adc_conversion_event_clean...
