I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
How to write driver for ADC by accessing direct registers of nRF52840 ?
I don't wanna use SDK APIs.
I wanna read LDR value connected to A0 (PO.3) pin in continous mode...
Dear all,
I'm trying to change the advertised device name during advertising depending on some variables.
I'm observing with nRF Connect and Lightblue, both running on...
Hi,
I have followed the steps for the 2 demos for nRF52840 DK, the Heart Rate and the Proximity demo. In both cases, when disconnected from the android device, the evaluation...
Heey everyone,
I'm currently working on a wireless application and we would like to have a range of atleast 300 meter. Yesterday I was testing the range between 2 SDK...
I work with Kenkou GmbH in Berlin. We are looking for Firmware Developers and Engineers with Mid - Senior experience to support our project. We are hoping to extend the visibility...
Hi All, Nordic,
In my application, I don't always need BLE connectivity, so I was hoping to disable the S132 softdevice when not needed. However when I do this FreeRTOS...
Hi,
I am working on a project with BLE and TWI module. With some help, I manage to set a TWI communication ( https://devzone.nordicsemi.com/f/nordic-q-a/29371/twi-issue...
Every once in a while I will get a failure that results in the app_error_fault_hanlder() being called and the following info:
ID = 1
PC = 0x14550
error_code = 0x495...
Hi, I use ble sniffer 2.0 beta with nrf51 (pca_10031_51296aa.hex). Is there a sniffer api documentation with description of the UART protocol (as with sniffer 1.0.1)?
Good morning everyone,
I am facing a weird problem concerning the use of the UART service.
I am currently using the NRF52832DK to develop an application. In a nutshell...
Hi Forum,
I am working on nRF52840 THREAD sleepy node and facing an issue in deep sleep mode. The current consumption in deep sleep mode is more-around 60-70 micro Amp...
Hello guys!
Are there any difference in using FDS library with a nRF52832 or with nRF52810?
I will explain.
I'm using a FDS for writing/reading to flash for 2 months...
(I've seen several other posts mentioning similar issues, but many of them haven't resolved or found a solution that seems to apply in my case.)
I have a custom board that...
