There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
I'm able to program the Soft Device (s110_nrf51822_7.1.0_softdevice.hex) from nRFGo studio and the compare is fine, but when I go to Keil uVision 5, I can build ble_app_beacon...
I use S130 on two nrf51822/PCA10001 boards. Each nRF scans and advertises simultaneously.
Scan parameters are:
scan_param.active = 0;
scan_param.selective = 0;
scan_param...
Is there a port of lib_aci for 16-bit processors? The structs in lib_aci written for nRF8200 are byte misaligned using a 16-bit processor. Seems to be almost a complete rewrite...
Hello,
I try to generate 4 PWM signals on an nRF51 DK board, but I have two troubles :
in the "Simple PWM", during nrf_pwm_set_value() function the TIMER is stopped...
Hi,
I recently ordered a usb dongle. It has PCA10031 board. The chip shows "N51422 QF ACAB" printed on it.
What SDK should I use? 6.1.0?
What board file should...
Hi!
I am using nRF51 SDK v6.10. I try to analysis the "spi_master_example". Source codes is
working well. But I couldn't understand how the "spi_master_send_recv_irq(...
I have an android application, which one can set and unset the LEDs of my nRF51422 EK. But sometimes when I click to fast the command will not be send. So I would like to...
Hello,
I want to know if it is possible to configure a button to act with different Detection delay.
In other words I want to have a single button to be able to trigger...
Do we have KiCad version of nRF51822 QFN48 reference design? We looking at open source toolkits, including Eclipse, so KiCad comes into picture.
Thank you in advance!
The test code:
int main(void)
{
sd_softdevice_enable(NRF_CLOCK_LFCLKSRC_RC_250_PPM_250MS_CALIBRATION, softdevice_assertion_handle);
temp_init();
unsigned int aaa...
I have a follow-up to this question: devzone.nordicsemi.com/.../
We are interested in dynamically changing the supply voltage because our space-constrained design requires...
Hi,
For my custom PCB, I am using the PCA10004 as reference in order to determine if the maximum possible range has been achieved. However, I am seeing only about 20 feet...
Hello I'v just ordered a NRF51-DK kit.
I'm looking at the different tool chain. In my application speed is critical 16Mhz is actually bearly enough, so my question is:...
I have a USB dongle with an nRF24LU1p that has a few SPI pins but is missing the RESET pin. I would like to be able to program it via SPI but the SPI programming protocol...
nRF51 RTX 4.74.0-3
SoftDevice S210 V4.0.1-3
Created a timer for 5 seconds interval.
It turned to be 4.4 seconds. with or without softdevice enabled.
Anybody else has...
