Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi,
while flashing the device i get "Contents mismatch at: 0001C1C0H".
I am not sure if my IROM1 and IRAM1 settings are setup correct in the Target Settings of my Keil project...
Hi,
i have two microcontrollers: STM32F401 and nRF51822. They communicate by uart with flow control. I use 110 Soft Device from SDK 10. The maximum baud rate when communication...
Hi All,
I am trying to update the HEX file of LED_mesh example using DFU bootloader over-the-air. The LED_mesh application HEX file gets uploaded successfully by bootloader...
Hi Nordics,
I copy pwm sample code into my proximity project, to drive a buzzer .
I init pwm before softdevice. but, once "SOFTDEVICE_HANDLER_INIT" is excuted, the buzzer...
Hi,
i have a problem with nRF51 an nRF24LU1+. I use S110 and micro-esb library. I can switch beatween poroperty RF and bluetooh ( never run both in the same time ). When...
I wanted to use the SysTick timer for timing in my application, but even when writing a handler and trying to set it up, it doesn't seem like the interrupt is ever triggered...
hi I am i using Keil to debug the progam, it seems like that the printf() function can't work in keil, so i use jlink RTT to perform the printf function to collect data ....
HI,
i want to have a application in which a timer timeout say 5 second. and during this timeout there is another timer say 1 second. whenever the 1sec timer timeouts then...
Hi,
The function sd_ble_enable(ble_enable_params_t * p_ble_enable_params, uint32_t * p_app_ram_base) requires now the application RAM base address! Is it 0x20002800?
Hi ~
I use nrf51-micro-esb on GitHub
In Tx-Device: auto sent (data+1) to Rx-Device
But Rx-Device receiver data still the same not Increment....
why in Rx-Device...
Hi everybody
Since quite a long time since my last visit here. Now I come back because a new project using the NRF51822. Because now I'm using the NRF51822-CEAA, I can...
Hello,
I am developing an application where in i want to create a network with One central[not a mobile,pc,tablet etc] and multiple peripherals connected to the central excahnging...
HI,ALL
my Project can not exit the GPIO INTERRUPT HANDLER.
following is my project.
include "nrf_gpio.h"
include "nrf52.h"
include "boards.h"
define BUTTON_1...
I have found the bellowing code which was in s130/ble_gatts_struct_seriallization.c of nRF51_SDK_10.0.0 : ( ble_gatts_attr_md_enc)
/* serializer does not support attributes...
