Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
Hello, we are trying to get a new laptop compiling and debugging with an older project. The old project uses SDK5.2 and SoftDevice 6.2.1. When we open it we get the error...
Hi Everyone,
I have problem about debugging program which for my nRF52810 custom board. I am using SEGGER IDE. I changed ses_nrf52810_Vectors.s and system_nrf52810.c files...
Hi!
We'd like to include a battery-powered remote control in our Bluetooth mesh network, i.e. we'll have a need for low power consumption.
In our mesh, devices may opt...
Hello everyone. I'm using an nRF51 with SDK 15 for a 'peripheral beacon example'. For compiling, I'm using segger embebbed studio. I have another bluetooth module(looks like...
Hello, I am trying to fabricate a board based on the Thingy design, including the accelerometer.
I positioned the components, traces, vias and pads following some recommendations...
Hi all,
Currently i am working on multilink Central and peripheral communication, now i want to do two way communication for the single central and multiple peripherals...
I am trying to use the sdk_config.h file from SDK15 to setup a custom board with a nRF52832. The nRF5283 connects to three SPI peripherals. For ease of software development...
Hi. I'm using nRF52832 SDK 13.0.0 as peripheral.
My device can be always connected by any central.
So some centrals may continue to attempt to connect to my device. I...
Hello!
I am developing a bracelet product base on nrf52832. I have a problem with softdevice's power consumption , when softdevice enabled,the power comsuption will rise...
Hello,
I am developing a basic application on the nrf52832. I am using the SDK14.2 and freertos (two very basic task).
I basically have a problem when I set a uint8...
I want to use app timer to get an power saving delay to wait some external chip operation done. So I use an app timer to set a flag when timer expired and in the wait function...
I need to implement UART service in such a way that it should act as both central and peripheral at a time.
I am using nRF52832 board and SDK 15.
I want to know which...
Using
- nRF5_SDK_15.0.0_a53641a
- gcc-arm-none-eabi-6-2017-q2-update 6.3.1
If I enable APP_TIMER_KEEPS_RTC_ACTIVE in the sdk config, setup the app timer with this...
I am currently working on implementing The Smart Beacon Kit with the Eddystone protocol. I only have basic knowledge in C, but I have successfully implemented the nrf_beacon...
Does it use the swi to guarantee the event realtime performance. What I need is, when an interrupt happen anytime, I just put an event to the schedule, and the schedule will...
