I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Hi,
after migrating from SDK12.2 to SDK14.2 we encountered a problem with GAP Security.
When setting optimization to -Os, the program fails with BLE_GAP_EVT_AUTH_STATUS...
Hi all,
I am trying to use uart-app (segger example in SDK15) to generate hex file, which will be programed to nRF52832 later with Softdevice by nRFGo Studio. ((Instead...
Hi,
we are using the NRF52840 DK and we would like to use our own antenna. We saw on others posts that we have to connect it to the J1 connector's place.
We have some...
Based on the Product Specification v1.0, the antenna load impedance should be 15Ω+j88Ω.
I checked the antenna impedance based on Figure 32.
The simulation result is...
During the development of nrf52832 (SDK14.2), I occasionally get NRF_FAULT_ID_SD_ASSERT error. When the NRF_FAULT_ID_SD_ASSERT error occurs, I can only get the information...
Hi Nordic,
I am working on a BLE based application. In my application, I am forced to use SPI and TWI of same instance.
I am using SPI1 and TWI1. Earlier I was working...
I'm adding key protection to DFU, a batch script is creating the bootloader_config_default.json. I'm using mesh SDK 2.0.1, but started developing using Mesh SDK 2.0.0. When...
Hello everyone,
my question is related to the time interval t TXEN = 140 μs from the radio timing table in the datasheet of the nRF52832-SoC ( http://infocenter.nordicsemi...
Hey Guys,
I am facing problem with building bootloader_secure example. I am using makefile for this purpose.
I am tryng for buttonless dfuimplementation, but the first...
Hi, I was trying to measure the current consumption on my PCA10040 dev board.
I have followed the online guide to prepare the board. However, when I connect the Amp meter...
Dear Nordic Team,
Thanks for supporting. For secure DFU successfully worked with nRF51422 (DK51 PCA100028). But its not work with my application board based on nRF51822...
Can anyone explain SAADC code under peripheral in SDK 15.00 for nrf52dk? and how can we use the data of analog read in ble to send the analog read data?
Hi,
I'm having problem with flash storage. First it's flashed with the writing code uncommented. Then I reflash it with the writing code commented like in the snippet...
Hi all,
What I need to do for detection of nRF52840 PDK as /dev/ttyUSB0 when connected to LINUX PC?
I have tried all serial examples but every one is detecting PDK as...
