I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
HI Teams
I referenced the Thingy91_X design. The MCU nRF5340 connects to the nRF9151 using two UART interfaces, but AT commands should only require one UART.
Under what...
Hi.
I've been developing with nRF54L15DK.
I added below in prj.conf.
Indeed, I could confirm CMSIS-DSP function normally running in main.c.
In my goal, I would like...
Hello, I'm running an example of channel sounding using nRF54L15.
The build is fine, but the following error occurs during flash.
Python is using 3.12.4 version. As you...
Hello everyone,
Currently we're trying to get the full WiFi stack working on nrf7002dk. We decided to look into the power consumption of the DK board itself as a point of...
I'm using 3.0.1 to compile an app for a nrf5340dk. It is building for 2.9.1, but errors on 3.0.1:
Line 51 is the first line of:
I thought that was the node label...
This is the power supply system in the nrf52832 development board. The manual means that when 1 and 2 are not powered, 3 is used for power supply, that is, cr2032 is used...
I have created my own project and board files for the development board I made. I have 3 I2C busses for different power domains, one SPI bus, and UART for debugging, so 5...
Our nrf9151 boards are getting stuck when nrf_modem_lib_init() is called.
We just see this line. Usually, the device gets past it in less than a second.
[00:00:00.376...
Hi.
For a while I have had some issues with the toolchain when using the nRF connect SDK in visual studio code on windows 10. I believe it was after installing SDK version...
This is a product based on nRF52832, which uses BLE Bluetooth to scan iBeacons and communicates with an LTE module via UART for data reporting.
It occasionally enters the...
Hi,
I'm using the nRF52832 with SDK version 17.0.1.
I've noticed that when the device wakes up from NFC and remains in proximity to the NFC field, it sometimes experiences...
Hello,
I'm looking to get XInput working on the nRF52840 so that our device can appear as an Xbox-compatible game controller. I'd appreciate any guidance or recommendations...
Hello Nordic Support,
I am developing a bare-metal, non-secure firmware for nRF9160 using nrf_modem from SDK nrfxlib v2.9.0 , without Zephyr or RTOS.
I followed the porting...
Greetings! I've applied all the optimizations in the books but I cannot get our application to be ~50% of the available flash memory on the NRF52832, currently it is precisely...
