I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
Hi,
I'm facing a weird problem resulting from the following code:
while((!twi_tx_done) && timeout--);
The main file and the MPU9150.c which includes this command...
Hi, I try to capture ipv6 over ble packet.
So, I construct system like, nrf dk 51(with sensor) - rasp
nrf-dk 51 is equipped with coap-server source and rasp doing like a...
Hi everyone,
I have a really weird problem.
I created a makefile based on Nordic's example from the app_template and created 2 additional targets, one called "debug" and...
I have upgraded my laptop to Windows 10 and all hell break loose.
When I either connect the board or the dongle, they are stuck in a loop of connect/disconnect behavior i...
hi,
i am using ble_uart example in which i am sending 3 byte of midi data
(90 1e 45 0a .E.)
i am getting (.E.) when i converts this ascii value to hex value i get (2e...
Im trying to provide DTM functionality for certifications tests. I can't setup an UART interface, I found the below code which tries to use DTM without UART. it uses channel...
Hello,
I've read a lot about trouble people had when they used bluetooth and flashed the rom without using the propper softdevice APIs.
What is the issue with concurent...
Good morning.
I ´m working with nrf51-dk, sdk 9.0.0 and softdevice 110.
I have done a proyect without softdevice, only uart and master spi (mode 0) and works perfect...
Hi, I flashed the Proximity Application to nrd51822,with s110_nrf51822_6.0.0-5.beta.
the chip run right, and I used the NRF Master Control Panel, when I write data 0X02 to...
Dear all,
I have tried using a setting a break point in main() of my program. Without running the softdevice, it is fine to pause in the break point and continue to run...
Hi,
I am developing a product using nrf51822. While pcb designing I am getting a clearance error. Please let me know how to resolve it. All the dimensions are 8mil in clearance...
Hi,
I am editing my question:
I have seen some strange behaviuor I could not explain. In order to test it I have made the next test program:
I am using the application...
Hi,
I recently bought the nrf 51 development kit. Before implementing a BLE application on the board I wanted to start with a simple application of blinking a LED by pressing...
1.I have a nRF51_DK and nrf51822(waveshare core51822)
2.Keil 5.18v and all of the needed software were Installed
3.s130 1.0.0 or 2.0.0 and sdk9.0 or 10.0 were used ...
