I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Hello,
i would like to turn off a sensor completely when unused and thought of powering it through the GPIO of the Controller.
I wondered if it is recommended or do the...
We have updated multiple android phones to nRF Toolbox for BLE app and we are all getting "Unfortunately, nRF Toolbox has stopped." error message when opening the app. nRF...
Hi,
I want to get a notification when the BLE event is started, in order to start a timer just after.
How can I get that?
I want to clarify my question :
My board...
I use the NRF 24AP2E in my communications, and I need detect if the communication is good.
I active the RSSI message, but in scanning mode I don't receive byte 0x20 in Measurement...
Hi All,
I am designing a circuit with nrf51822 and mcp25625 (microchip spi can interface). mcp25625 has an internal 16mHz xtal clock circuit and a digital clock out, I...
Hi, i'm kinda a newbie on this, and i'm trying to port the SDK available for arduino to a PIC, i followed the instructions on the SDK and also here
Now i want to verify...
I ran into an issue recently of attempting to make a pstorage_update call from the callback set in pstorage_register . It resulted in a difficult to track down error, so I...
I have a USB dongle of nRF24LU1p and it is identified as the Basic Remote firmware with a VID:PID of 1519:002B. I would like to reprogram it over USB but do not know how to...
For nRF 51822 radio transmission, the payload packet is started at the NRF_RADIO->PACKETPTR. Then what is the packet size? is there any parameters to control the packet size...
I should have an own function wich is called upon after Port 3 goes low. I haven't succeeded yet using ppi channels. (I'm using the NRF51422)
For the moment the code is...
Hello folks ;
I'm new here and glad to have such kind people around to see helping those other developers ..
Here is my question
I'm using one of the NRF24L01 modules...
Hi,
I'm using the attached circuit and we recently took our product to FCC testing and failed the 2nd harmonic because we were transmitting too much power.
I'd like...
Hi All,
We have been working on Arduino Mega board with BLE shield. We want to get the address of the BLE shield and we are using aci library for that.
I found this...
I'm in the process of designing a consumer product using the nRF51822. I'm using the "square wave" antenna and matching circuit exactly as the are in the development kits...
