I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I've got some timing-issues with the nPM2100. As I could not locate the relevant information in the datasheet, I'm requesting this here.
My PCB has an nPM2100 with a mechanical...
Hi everyone,
I’m using a custom board (a tracker) that can travel at speeds up to 65 km/h and transmits data regularly every 200 ms. I expect, therefore, that the inactivity...
I procurred two NRF52DK boards and in both the boards I am facing the similar issue of "Failed to Connect the Target". When I am running the nrfutil device recover command...
I noticed that the product information of the nRF54L15 series kit supports 4Mbps, but I'm unsure how to verify it. Are there any relevant examples available? I have currently...
Hi,
i acheived writting code that reconnects sequentially with multiple reflectors for my 1 initiator. When i am indoor i had good results, but yesterday i tried it with...
Hello Nordic Support,
I am developing a bare-metal, non-secure firmware for nRF9160 using nrf_modem from SDK nrfxlib v2.9.0 , without Zephyr or RTOS.
I followed the porting...
Hello
I'm using an external flash to store large files, but I’d also like to use the SMP service to exchange small files over BLE. For that reason, I want to create a LittleFS...
I'm having an issue with SPI communication. The problem is quite simple: if I use the Zephyr driver, everything works fine, but if I use the nrfx driver, it doesn't. The function...
Keep hitting my head on this inconvenient workflow.
Edit build config
Select target custom board
Build config
All OK
Edit config again
Target board has been...
Hello,
I am using the nRF5340DK and the PCF8574 with I2C communication. The issue I am encountering is that the function device_is_ready(pcf8574.bus) fails to initialize...
Behaviour:
Declaring a carbon dioxide attribute list with
results in
Using
results in
"zb_zcl_carbon_dioxide_measurement.h" and the macro "ZB_ZCL_CLUSTER_ID_CARBON_DIOXIDE_MEASUREMENT_CLIENT_ROLE_INIT...
Custom PCB with nrf5340/nrf7002. Currently was using NCS2.9.0, with WPA2-PSK connection to the wifi.
While trying to enable use of WPA2-Enterprise, I updated to NCS3.0.0...
Hello Nordic Team,
I am experiencing an issue when attempting to flash a Zephyr RTOS application (v3.0.0) to the Adafruit Feather nRF52840 Sense board using a J-Link debugger...
Hi,
The attached code is based on a sample code from NCS v2.9.1 and creates a LittleFS flash disk on external SPI NOR onboard nrf54L15DK. There is a mismatch in the code...
Hello,
I'm getting the below mentioned error when I try to build Light Bulb sample with MoveToClosestFrequency in LevelControlCluster .
/home/dotdll/ncs/toolchains/7cbc0036f4...
