I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hello everyone
I have a small question about Mesh_gatt_pdu_type_t in light_switch_example.
When my NRF52 connect with smartphone over BLE mesh proxy, my smartphone will...
I am developing my project in a nRF52832 custom board. I am working in SDK v12.2.0. My application program is based on ble_app_uart.
It seem a bug about the defined characteristic...
Hello All,
I have compiled and flashed fresh ble_sdk_app_proximity with armgcc to my NRF52DK(S132,SDK15.0.0). After connecting to the DK with nRF connect ios app I can see...
Hi All,
Am using SDK 11.0.0.89a8197 Device Manager,
I get this error very randomly .. My case is I allow only one device to bond with me , After bond I always advertise...
This question is similar to the feature request: devzone.nordicsemi.com/.../sdk-12-x-0-future-feature-requests
I have to evaluate if we buy Tracealyzer ( percepio.com/....
Hi.
I have a problem to understand what is the difference in SFR registers IEN1 and INTEXP.
Bit 2 in both of them is responsible for enabling 2-Wire completed interrupt...
Hi,
We are currently developing an app which require DFU.
As part of the bootloader development we would like to use the SWO in order to do a printf debug.
In the app...
Hi there,
I am looking to double check the state of NRF52840 while its reset is active.
I have found this thread regarding the NRF52832 ( https://devzone.nordicsemi...
Hi,
I am using sdk12.2.2 and customised nrf52 boards. I am storing 9000 records with 7 bytes each in flash.
After sometime I am getting buffer space full error and I am...
Hi!
I am developing anapplication on NRF52 DK. I need to preserve value between software resets and to do so i tried to use GPREG .
To set value i use code:
//set value...
Hello, I am a student studying firmware
I want to use SPI and UART in one project at the same time.
The soft program uses KEIL and is the latest version. Code generation...
I just received the PPK and use it for the first time.
I am trying use the PPK to monitor the current of an external board.
SW2 is set to 'external' and SW4 is set to...
I have downloaded both "nRF5_SDK_15.0.0_a53641a" and "thingy_sdk_v2.1.0".
After that I tried to build the "main.c" file of " thingy_sdk_v2.1.0" in keil uVision5 but it showed...
My nRF52840 custom boards seem to be unable to boot without RTT viewer started of JLink commander connected.
The hardware configuration is taken from the nRF52840 PS 1.0...
