to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
This fork of the MBED CMSIS-DAP firmware seems to be the latest updated one. The title says, 'Interface firmware providing USB CMSIS-DAP for debugging, USB MSD for programming...
Hello,
I try to change a value by using sd_ble_gatts_value_set(...). If there is a connection, this works fine. But now I have to change the value also, if there is no...
Hi again.
I'm using nRF52 DK board in Ubuntu. I can flash the device with the blinky example (I haven't yet tried the softdevice tough), but I cannot really get any traces...
20160316_113235.jpg Hi guys,
i have 20 nodes and a central in my network, that are very close to each other except central device ( All of nodes are in a approximately...
Hi,
I'm wondering why are there scan parameters on creating connection? If I refer to SD130, create connection function , there is a note which tells us that if scan is...
I have 2 existing products, one using the nRF24LE1 and the other having a 2.4GHz ANT radio. Is there a way to have the 2 products communicate wirelessly? If it is possible...
Hi.
Quest to get the toolchain working under ubuntu continues.
I've done the eclipse and jlink config as explained in the nrf51 linux tutorial (with of course keeping...
In an RFID application, we have nrf24l01+ and SMT32F4xx on the Reader and nrf24lu1+ on the tag.
The Reader is acting as multiceiver currently.
Pipe 0 and Pipe 1 are...
Hi Team,
Is it possible to develop MCP like other application which runs on Linux (say Ubuntu) using BLE dongle?
Where to start for this!? Any guideline or documentation...
Can smone help me:
An error pops-up…
“
RESTRICTED VERSION WITH 0800H BYTE CODE SIZE LIMIT; USED: 0DC4H BYTE (172%) *
“
This could be due to EVAL version of uVision...
So I'm using Keil v5.18.0.0, MDK-Lite Version 5.18, nRF Beacon app version 1.4.2, android 5.1.1, nRF51822, and nRF52832 micro-controller
I can successfully connect te bluetooth...
I use nrf51822qfaa ,s110 V8.00,keil mdk V5 ide.
does advertizing data Length can more than 31 byte? why?
ble_advertising_init(&advdata, &respadvdata, &options, on_adv_evt...
hello everybody,
I'm working in a project and faced some problems : article_1 & article_2
the final thing I did is as the second article, I do bonding & added the whitelist...
I want to make a BLE central A that can only connect to a BLE periperal B, and central A can not connect to periperal C,D,E...and other devices, even if they have the same...
Hi Nordic support,
I check the serialization page ( infocenter.nordicsemi.com/.../lib_serialization.html)
And prepare a connectivity board as below for my host system....
