Hello, I hope you are well.
I created a new driver for an i2c accelerometer with 2 gpio interrupts, but it does not build properly. When calling `static const struct device...
Hello everyone,
I'm working in a ble project that use uart interface. When I sent string data in nrf connect app, the uart_event_handle is not called.
I started my project...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
nrf5340DK
NCS 3.0.0
if I use sample zephyr/samples/boards/nordic/system_off it works fine and i can wake from sw0 press. but if i move the sys_poweroff() call int a...
Hi Team,
Recently we did a network related testing for our CL5G modem (nrf9160) and observed a problem, in this test we used a nmap tool, this tool will search for open...
Steps to reproduce the problem
Create a new application based on the Matter Light Switch example of the SDK 3.0.2
In prj.conf set CONFIG_CHIP_FACTORY_DATA_BUILD=n
...
Hello,
I am new to nRF development. I am going through the nRF Connect SDK Fundamentals course.
I wanted to configure a GPIO on the nRF52833 DK board as an output and...
Hi，the Nordic team
I use the SED device by system on mode.I found that my static average power consumption increased by more than 20 ua after I defined an IO port to use...
Hello, I'm running an example of channel sounding using nRF54L15.
The build is fine, but the following error occurs during flash.
Python is using 3.12.4 version. As you...
Dear Team,
I have recently acquired NRF54L15 Development Board for evaluation and from Day 1 experiencing issues with BLE.
I am running simple Zephyr-based BLE Peripheral...
Hello everyone,
I am a EE student and this problem came up during my first big project in zephyr. I'm trying to connect a pwm peripheral (pwm1) to the timer 2 hardware timer...
Hello everyone,
I have an nRF5340 microcontroller (NORA B106 module), and I want to connect a square wave signal to one of its pins to read its frequency or count the number...
Greetings,
I have previously added the LittleFS to the internal flash of the nRF52840 with success using the available documentation. Our .dts & and code is shown below...
Dear all,
I am wondering, what is the reason for C13 being 3.9pF for QFN package, while there is no capacitor on WLCSP reference design? Could we use like 10nF instead?...
Hello everyone,
I tried reading around the devzone and the infocenter , but I still didn't manage to solve my question.
In my scenario I'm using:
an nRF52832 as a...
I am trying to create a partition on mx25r64 using partition manager on my nrf52840dk. Below is my overlay file
Below is my prj.conf file
Below is my pm_static.yml file...
I have a couple questions regarding the Bluetooth Mesh provisioner role and TF-M builds.
I am using an NRF54L15 and currently swapped to v3.01. Previously on versions <3...
Using FreeRTOS and SDK 15.3 on nRF52840 and SES, SD 140
I'm following along with the NUS example project in this particular release and have a problem I'm a little stumped...
I'm having an issue with SPI communication. The problem is quite simple: if I use the Zephyr driver, everything works fine, but if I use the nrfx driver, it doesn't. The function...
Hello.
I'm having issues with a custom design board using NRF52832_QFAA SOC.
This is the snippet of the schematic design that my group created:
This board uses internal...
