Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I am using SDK 12.2.0 with soft device s132 3.0.0 using NRF52 Development Board(PCA10040).
I want to update Battery level to central device/APP.As i want to use code for...
Hi,
I am working with a nRF51822 chip placed on a Ble Nano v1.5 board and I would like the schematic of Ble Nano v1.5. Could anyone tell me where I can find the schematic...
Hello,
I am using pca10028 and sdk12.2. I am trying to take sensor reading via TWI and I want to send this reading over ble. So I am trying to add twi files in ble_app_template...
I am attempting to increase the queue size for handle value notifications to support a higher number of packets per connection event. However, I am unable to set the queue...
Hello,
I'm working on nRF52832-DK with SDK11 on linux.
Is there an example to use whitelisting ? I'm trying to use HIDS_Mouse but it's not working.
How can I write...
i have learn how to program nRF51 DK with and without softdevice. Now i want design code as per my requirement... but find difficulty to understand given sequence of code...
Hi,
I am working over nrf51822 ble and I have some security issues with that. I'm programming an android app to connect to the nRF51822 (peripheral). Without any security...
Hi.
I'm trying to control a keyboard and a mouse with nRF24LU1+ USB dongle module.
www.nordicsemi.com/.../nRF24LU1P
I downloaded this link below from the Nordic website...
1\select zip file
2\scan and select nrf51 dev
3\upload.
then the nrf51 enter dfu mode, and can scan the dfutag ble dev. but the ADDR auto add 1 . Wait about 10 seconds...
Hello everyone.
I've got the nRF51822 Evaluation Kit and Dongle. The heartbeat demo is working, so I got the toolchain -- Nordic, Keil, Segger under Win7 -- set up correctly...
Hie,
Is it compulsary for us to send only 20 bytes of data or less than that in one packet in BT5 as we used to do it in BT4 to make BT5 compatible in communicating with...
Hi,
I want to develop a product with Bluetooth 5( NRF52840) capability, before starting development I wanted to know will the Bluetooth 5 devices(Peripheral) will be compatible...
Hi. When i use ble_app_uart i have problem with my device over uart. It does not response to my commands.
I'm using custom pcb based on nrf52 with nrf UART v2.0 android...
I have moved on to SDK12. But one old project using SDK10 now requires a 128 bit UUID.
I keep getting hard fault when I add UUID.
I noticed that there is no vs_uuid_count...
Hi Team,
I am using nRF5_SDK_11.0.0_freertos_dfu_060516.zip SDK. I have added NUS service with UART configurations in this code successfully.
When I am commented the DFU...
