Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
tl;dr: UART transmission sometimes stops and never resumes. Only a
power cycle resolves the issue; a system reset is not sufficient. The
problem only occurs when flow control...
Hello,
as far as I have gathered, it is possible to use multiple peripherals on one device with the current alpha release of the S132 Softdevice. What I did not understand...
Hello,
today I had a problem where a timer was causing my device to reset after a while, because the app scheduler queue got full and it was raising an NRF_ERROR_NO_MEM...
Hi!
I am playing with NRF cloud and Android phone gateway. I am not able to find out how to carry out firmware update over NRF cloud. Would you please shed some light?...
I am developing an application with a single service that has a single characteristic with read and write operations.
I want to give the ability to writing to this characteristic...
Hello,
I am working on a project with STM32 master and nRF51822 slave connecting to Android/iOS mobile apps.
I send the advertising parameters from STM32 to my nRF51822...
Hi,
I am new to firmware engineering. I have a simple and basic question.
If there's Timer A and B, and both interval is 100ms, what happens to the timeout handler functions...
I want to add some configuration files to nrf52, so can I write data in flash and read when I want.......I have the example code of twi master_twi slave but it engages the...
I have followed the instructions for sniffing ble packets with wireshark. Errors would occur when using 2.2.5 so I switched to the latest development version. See this question...
Hi, I am developer of indoor location tracking solutions for asset tracking applications, actively looking out for new technologies, i would like to understand what are the...
Normally I am using nrf51 for peripheral(sdk 8.0.0 s110) and central(sdk10.0.0 s130) device. But I want to use nrf52 for just central device. I tried nrf52 for central(with...
Hello All
Currently i am using nRF51422-DK (PCA10028) Board .I am planing make mesh network using nRF51 devices.i go through the mesh network introduction document which...
Hi,
I'm trying to set a button as an interrupt source. I wrote this code:
void Init(void){
pwrmng_MainStatus = PWRMNG_STS_STARTUP;
//LED
#ifdef DEBUG_LED
nrf_gpio_cfg_output...
I want to read the status of LFCLK,but I find that ,the value I have readed is awayls zero! my code is follow :
LFCLK_State = ((NRF_CLOCK->LFCLKSTAT) >> 16) & 0x00000001;...
Hi,
I had done secure OTA in nRF51 DK board using SDK 12.2.0 and s130 2.0.1 softdevice. Now, i am trying to same thing with my custom Board RL-51822-A1.
For that first...
