Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi guys.
I want to make use of CLI in my existing project based on ble_app_uart .
I was looking at the diferences of there sdk_config.h and there is a lot of stuff happening...
sd_flash_write(((uint32_t *)storage_addr),
(uint32_t *)p_data_addr,
size / sizeof(uint32_t));
why here size value is divided by sizeof(uint32_t).
what is byte value...
Hi,
I'm trying to adapt the HRS/RSCS relay example from the SDK to use the Nordic UART service instead. Currently I can connect to the central just fine, but if I try to...
I'm using RTX timers on NRF51 and I'm getting a 7ms per second error. (I.e. osDelay(1000) takes 1007ms).
It appears that NRF_RTC1 is configured incorrectly in SDK examples...
Hello, I am working on NRF52 customer board + SDK_13.0.0_04a0bfd
I start with ble_app_uart example, I use interrupt tigger a repeat timer(500Hz, 400 times) to sample 6 channels...
I'm having major troubles with my debugging setup using a nRF51 DK (PCA10028 V1.2.0).
When I try to connect to the board I want to debug/program (which has an BlueMod ...
Hi Everyone,
I'm currently busy going through the OpenThread API and examples to better understand what all the functions do. However, I don't fully understand where the...
Preferences: nRF52832 chip, s132_nrf52_4.0.2_softdevice
Two or more nRF52832 chip are connected to iOS and Android.
And do bluetooth off in smart phone.
this case, bluetooth...
This suggests it should be possible to change the beacon advertising content in response to events such as a GPIO input.
I'm using nrf52 DK running the beacon example (SDK...
Hi,
What should I add to the makefiles to be able to generate an assembly code? Something similar to what is seen in the debug mode of Eclipse. I have tried -S/s but it...
Hi
I want to porting to nRF52840 but since S140 SoftDevice Specification documentation doesn't exist
I can not proceed with porintg.
I need S140's detail memory map...
I am using s132_nrf52_3.0.0_softdevice.hex and sdk12 and compiling with arm-none-eabi-gcc. The problem is that the bluetooth set up just jams at:
// Enable BLE stack.
...
I'm trying to get my nRF52 BLE peripheral to connect to my phone while its screen is off and it's in sleep mode. Other consumer BLE peripherals that I have can connect to...
Hello
is this possible to reset the timer.
for example i set the timer for 10 Second.
when he reach up to 5 second then i would like to reset the timer.
i found no function...
