I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Is there an AT command (For modem firmware >= 2.0.2) that can be used to validate whether the LTE modem can communicate with an external MIPI RFFE switch (for example on a...
Can Nordic share specific instructions on how to enable hardware tracing?
I've received the following patch from Tomasz, however I still see "trace clock missing" in Ozone...
Hi
our last product is based on nRF5340 and now we start a new design based on nRF54H20, and its essential for our design, i checked alot but there is no datasheet, reference...
just passed Cellular IoT Fundamentals while I was waiting for my nrf9151dk to be delivered... Now that I have the DK I can't get the dk to be provisioned...
I couldn't get...
NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
Hello!
For beginning with nRF51 I chose BLE Nano set of boards (BLE Nano + MK20 USB donbgle) and it was of great help to easily begin with BLE.
So far, we came to the need...
As an experiment, we want to implement soft power off for nRF52 with external components. We want to keep the entire circuitry entirely switched off, and after a press of...
I do not use board.h nor bsp* in my project, and also I am not initializing the pins that I do not use in my program currently - so P0.17 is not initialized and setup. However...
Hi all,
I am new to nrf51-dk and I am using nRF5 SDK v11.0.0.
I wanted to perform the task below.
When the DK is turned ON, read on board push button status.
If button...
We are implementing scan functionality in nRF51. I would like to understand if anyone has tested or tried to scale this functionality when there are thousands of beacons around...
Hi everyone,
I was wondering how GAP calls and events are synchronized within the SoftDevice.
Example:
// conn_handle is updated in the CONNECTED and DISCONNECTED...
The Android Master Control Panel app has an option to remove bond information (which works). But the API for it is hidden .
I'm just wondering if you use reflection to...
We are trying to replace an existing solution that uses a custom Service with 4 Characteristics. Unfortunately none of those share the same base UUID.
Basically the Service...
Ok - I'm trying to get my arms around this bootloader process.
I am using the nRF5_SDK_11.0.0_89a8197 SDK along with the PCA10040 develeopment kit.
I also am using IAR...
I'm trying the run the smart remote 3 v1.1 firmware built using IAR.
The firmware fails to init the touchpad and enters a forever loop.
The program only builds with optimization...
Hi,
I am using nRF52832 with S132_V2.0.0 and SDK_11.0.0. In my application i plan to use RFX2411N PA/LNA module. In datasheet of RFX2411N, I found that it can be used in...
Trying to qualify our design with Bluetooth SIG.
NRF51422 QFN48 nRF51 SDK v10.0.0 SD 310
When I use QDID 62791 to generate a test suite for PTS on the SIG website, the...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
Hello,
I am working with the nRF52 DK, SDK 11 and especially with the ESB protocoll. I started with the provided example esb_low_power_ptx/prx.
In the documentation...
Hi,
I wish to encrypt my application to protect my code. I've tried running my hex file through openssl
openssl enc -aes-128-ofb -nopad -nosalt -e -K XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX...
