I was implementing custom services and characteristics(softdevice:s140, ble) on the nrf52840 dongle, however I couldn't get it to work, even though my code seemed correct...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
Hello,
I've got a problem with my nRF51 DK. When I attach it to the USB port the drive doesn't appear on Windows explorer and green diode doesn't flash too.
I've been...
By design, the TI LP55231 LED driver IC will fail the TWI write of the reset register (0x3D). It's necessary to reset the IC in an edge use case. I'm using the nRF51822 HW...
Hi,
I want to write a characteristic, the value size is fixed, for example the size is 4 bytes. When I try to wirte 6 bytes from the client, the first 4 bytes is writed succesfully...
Hi all,
I have the nRF52 DK programming consistently without any trouble both on Kiel and using the nRFgo Studio.
My problems arise when I connect a 3rd party module...
Hi,
im trying to set up 3 PWMs for simulating a RGB LED with the 3 leds on the nrf52-dk.
I need the following behavior:
pushing on a button increases the width of the...
Hi,
I have implemented a custom application(Lets name that file app.hex) which works and sends the data to phone via BLE on my nrf51822 DK. I am using the s110 v8 softdevice...
Due to some constraints in the manufacturing process of my product, there is substantial mechanical variation in the BLE antenna. I can constrain this variation to a degree...
Hi,
I am trying to program MDBT40 with Jlink and having some problems.
Here is the scenario:
I have two versions of the MDBT40. One that I took off a BLE NANO (RedBear...
Hi,
I tried to get the sample ble_app_uart to work on NRF51422_DK with the S130.2.0.0 soft_device.
The compilation and programmation of the board is OK.
The soft run...
Hi all, i recently posted some topics about my application to receive support, everything went good but now i need to add a last step to the project, and i would like to have...
I am using nordic_sdk_10 for PCA10001. what are the BSP changes and config changes needed after replicating PCA10028 for DFU over UART.
I just changed CFLAFS & ASM FLAGS...
Hi,
I am storing data using pstorage module but when i power off my nrf51-dk board, the contents get deleted and not retained in memory. What could be the reason for that...
Hi,
For a new design with nRF51822-QFA, planning to use Johanson Balun and Chip antenna as shown in attached diagram. Not using any tuning components between Balun and...
