I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
We have a new daughter board connected via I2C to an Atmel controller. What we need to do is load the right softstack onto the NRF and then send the needed commands to tell...
Hi Guys,
We have schematic of future NRF 51822 project, who can help us with PCB design? Or who can suggest me where i can do it?
PCB.DXF
schematic.pdf
Hello All,
I am trying to build a BLE peripheral project with RTX OS which is using S110 Soft Device and bootloader is also there in Flash memory region. So when I am trying...
I am just beginning to develop with BLE.I came across the nRFgo Studio through Nordic and BDS through the bluetooth SIG.
1]What are similarities/differences between the...
Hi.
I want to active HW timer with SoftDevice 7.1.0 .
Timer operation is good but I can not stop the timer.
The power consumption is 200~300uA after timer expired ( or...
Hi,
We would like to use NRF52832 chipset for our project, and we need to configure 11 pins as GPIO interupt , Is this possible ? How many pins we can have as interrupt...
I have Bluetooth iOS app communication with my nRF51822. I notice that when I connect the the nRF, the first GATT write event is always the same:
p_ble_evt->evt.gatts_evt...
I am using SDK v11-alpha2 and following the BLE Services and BLE characteristics tutorial.
When calling sd_ble_uuid_vs_add as the Characteristics tutorial asks, I get a...
HI ,ALL ,
i have change the project for the purpose of enter a six digit key at cellphone side to enable the notification with the board(52382).
But when i input the...
Hello, I looked througth the devzone but didn't find direct answer. So created new one.
RM v3.0 states chapter 12.1.19 "Reset behavior" with table. However, it is not clear...
Hi,
I have to check every 10 minutes the battery level when BLE is connected .
I have found in this forum this source : github.com/.../main.c
As the source date is...
Hello All,
I developed one project in nRF51822 with S110 Soft Device based on following configuration.
SDKv10.0.0
DFU capable
RTX Support
And now I want...
Hi ,
I am using Soft Device S130 and NRF51 kit PCA10001. I am using SDK 11.0.0-2-alpha .
I am trying to test the Alert Notification Service Example as mentioned here...
