I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
I'm trying to send data over UART... started off using the examples from the SDK.
When I run the code on the dev board, I can get it working. When I load the code onto...
I want to use ESB protocol, with app_timer module to generate timer interrupts. Is it possible?
If yes could you please send some example codes for it? thanks
Per the nRF51822 product specification the NVMC ERASEPAGE operation takes up to 22.3 ms, about 730 ticks of a 32 KiHz clock. This is 365x the maximum delay between the watchdog...
For evaluating the nRF52 for a project I need to demonstrate BLE 4.2. secure pairing with NFC
I want to use two nRF52 eval boards but I need two software examples: One...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
Hi all! I have an application where i perform a "write command" with a device on the characteristic value of another device (client). I want on the client that when it receives...
Hello ,
I have an idea of using nrf51DK along with another external microcontroller both of them are connected via SPI inerfacing the aim of my question can i use the bootloader...
Hi, I am working on Eddystone project i.e nrf5-sdk-for-eddystone-master now I need to add the dfu support to it the problem I am facing is explained below
In SDK nRF5_SDK_11...
Hi,
I am using nRF51422 with S130. I want my application to blink a LED every one second. For now I am using App Timer which solves the purpose but the current consumption...
Hi, I have been trying to figure out how to get the IF BOOT/RESET button on the nRF52 micro-controller working. I have defined "CONFIG_GPIO_AS_PINRESET" under C/C++ in the...
Hi all,
I seek an advice on the passkey topic. Have been researching the topic all day but still have some confusion. I am running SDK 10.0 ble_app_uart example on nRF51...
I have a quick question pertaining to the instruction sequence that occurs immediately after the anti-collision completes:
I am working on implementing a Type-4 tag library...
Following this thread , I tried to upgrade my dongle from s130 v1.0 to s130 v2.0.
I'm using windows driver 0.5.0
Tested both binaries for 0.5.0 downloaded and compiled...
