pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
Hi Guys,
We have schematic of future NRF 51822 project, who can help us with PCB design? Or who can suggest me where i can do it?
PCB.DXF
schematic.pdf
Hello All,
I am trying to build a BLE peripheral project with RTX OS which is using S110 Soft Device and bootloader is also there in Flash memory region. So when I am trying...
I am just beginning to develop with BLE.I came across the nRFgo Studio through Nordic and BDS through the bluetooth SIG.
1]What are similarities/differences between the...
Hi.
I want to active HW timer with SoftDevice 7.1.0 .
Timer operation is good but I can not stop the timer.
The power consumption is 200~300uA after timer expired ( or...
Hi,
We would like to use NRF52832 chipset for our project, and we need to configure 11 pins as GPIO interupt , Is this possible ? How many pins we can have as interrupt...
I have Bluetooth iOS app communication with my nRF51822. I notice that when I connect the the nRF, the first GATT write event is always the same:
p_ble_evt->evt.gatts_evt...
I am using SDK v11-alpha2 and following the BLE Services and BLE characteristics tutorial.
When calling sd_ble_uuid_vs_add as the Characteristics tutorial asks, I get a...
HI ,ALL ,
i have change the project for the purpose of enter a six digit key at cellphone side to enable the notification with the board(52382).
But when i input the...
Hello, I looked througth the devzone but didn't find direct answer. So created new one.
RM v3.0 states chapter 12.1.19 "Reset behavior" with table. However, it is not clear...
Hi,
I have to check every 10 minutes the battery level when BLE is connected .
I have found in this forum this source : github.com/.../main.c
As the source date is...
Hello All,
I developed one project in nRF51822 with S110 Soft Device based on following configuration.
SDKv10.0.0
DFU capable
RTX Support
And now I want...
Hi ,
I am using Soft Device S130 and NRF51 kit PCA10001. I am using SDK 11.0.0-2-alpha .
I am trying to test the Alert Notification Service Example as mentioned here...
Hello!
I'm trying to use the nRF51422 internal ADC to send the value over BLE then monitoring the value received on the nRF Master control panel on Android phone but I...
