i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
I am using a nRF51822(pca10028) for current measurement. I had set up the devices as told in user guide. I am using SDK 11.0, softdevice s130 and default ble_app_pwr_profiling...
I am trying to make a custom BLE service and be able to do debug it with UART at the same time.
Just trying to print some UART messages at some points in the code.
However...
I have a couple of questions with the MCP.
Before knowing MCP, I've been connecting with my nrf51-DK with the nordic master control app installed in my smartphone. Opening...
I am doing burst transfers using exactly the code suggested here devzone.nordicsemi.com/.../
The problem is, the data is received three times by the receiver (three times...
Hi!
I question the use of Software Interrupts and especially SWI3.
I'm currently developing an
application on nRF51422 based on
SDK10.0.0 and SoftDevice S110
v8...
I know that it can be done and I have read the other posts. I'm still running on SDK8.0.0 with both a S110 and a S130. Using wireshark and the nordic sniffer firmware on a...
hello everybody,
I need to send some data on the value attached with the notification:
/**@brief Function for adding the notify Level characteristic.
*
* @param...
My application need more than one of the host in the same area, we will set difference pipe of each host, we want to know the area already exist which of the pipe. Then we...
Is there a way to avoid fees, and still use BLE? Do I need to change UUIDs or leave them be?
If not can the nrf51822 be used to just use the pure 2.4 ghz protocol and DFU...
If a BLE device using nRF51822 has a freuqency drift around 80kHz (BLE limit is 50kHz). All other measurement item like ICFT can pass the BLE spec. Will the performance of...
Hi, this is my very first post to this forum.
I just received my nRF51 DK, so I installed a lot of stuff. The blinky example is running fine.
A question about nRFgo Studio...
hi, i am going to make a simple PWM with SDK 6.0.0, nrf51822 and softdevice.
first, i use ble_app_uart example as a base code, because i need to BLE communication with...
I have purchased a BLE module using nRF51822. I have used Agilent N4010A to test the RF characteristic of the module. For first log of the BLE moudle (300 pcs), all 300pcs...
Hello,
I want to serve webpage from nRF52DK via BLE.
In fact I got the kit specifically for this task.
I have installed GCC, Eclipse and SDK for IOT.
Thanks to the nice...
