Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hello! Developer,
Does anyone know how to transfer and store the value as big endian on memory address on nRF51 and send it over BLE to display value on MCP as big endian...
Hello!
I'm trying to get the 16 bit ADC value as 2 of 8 bit array from nRF51 development kit over bluetooth to MCP, but when it displays on the MCP the value is "swap"...
Is it a good idea to use nRF51 standalone as an Application Processor and also as BLE connectivity chip?
OR
Is it a good practice to use a separate Application Processor...
I have a question on - to me - seemingly weird behavior about copying data out of the event from the soft device.
Situation: I have a 32 bit integer characteristic which...
Hey all!
Newbie here. I developed and tested some code on an NRF51DK easily enough using mbed, and now I'm trying to put it onto a PTR5518 module from Xuntong (which I...
Could you rub my nose in Bluetooth SIG Core or just explain what does chip do when switching to very noisy channel? For example Wi-Fi working very close to our device.
Hello:
I have read the documentation but I cannot determine if INPTR and OUTPTR can be set to the same memory address? I will try it to see what happens but it would be...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi,
Everyone,
I found out on that ble_app_power_profiling application is developed for Lower power current consumption....as It keeps system in the system_off_mode until...
Hi,
I am trying to measure and minimize current consumption .....
Following previous question on this forum,I found way to measure current on NRF51 DK by cutting SB9....
Hello Everyone..
i am new to nrf52 and this community.
i am using nrf52 and android master control pannel.
in my code i define my custom uuid base to ..
//430Cxxxx...
Hi, I'm looking for an easy way to use the UART in blocking mode (or something similiar) with a receive buffer that is filled in background:
If possible using EasyDMA...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi everybody
I am making a custom board which using ANCS (nrf51 sdk 9.0.0, softdevice 110 ver8.0.0). I saw on the original code have button_led_init() function to initiate...
