I have a nRF54L15 firmware built on NCS v3.0.1, with image encryption enabled in mcuboot. Firmware needs to be updated to new version built on NCS 3.3.0.
In NCS 3.0.1, image...
Hi folks,
I am working on an nRF52840-based custom board using nRF Connect SDK v3.2.4 and have observed an issue related to runtime power management and PWM.
Environment...
Hi, is there a sample using nRF7002 on nRF54LM20B SQSPI (or could you share an appropriate devicetree)? I have been successful using the nRF54LM20 DK + nRF7002 EBII combination...
Hello.
I have nRF52840 USB Dongle connected to PC with nRFConect desktop application 4.0.4
I'm trying to connect to our custom BLE peripheral device, which advertises...
Hi all — I'm developing a custom nRF5340 development board (Raytac MDBT53-1M) and would value the community's honest read on whether it's worth producing.
The goal is...
Hi,
I am using two nRF52833 devices with the nRF5 SDK. They are paired and bonded to each other. Occasionally, I encounter the following error in peer_manager_handler :...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
Are there any up to date samples for running BLE on nRF9160 development kit? I've tried building the following sample: https://github.com/nRFCloud/lte-gateway/tree/main for...
Hewy there:
I have a custom nRF52833 board with NCS v3.1.0, using ESB and USB CDC ACM. The external 32 MHz crystal is oscillating fine — we see a clean 32 MHz sine wave...
Hello!
I am having problems reading the SIPINFO on the SoC. I started with the TFM sample and added some lines to read the silicon version. added lines:
printk ...
Hi Nordic Team,
I have been working on the Bluetooth Channel Sounding (CS) Initiator and Reflector samples using nRF Connect SDK v3.3.0 on nRF54LM20B devices , and I was...
I want to expand the flash allocated to mcuboot on the NRF desktop, but it failed to start after compilation
The following is a flash layout that can be successfully launched...
When implementing a custom service, the order is usually Generic Access, Generic Attribute, and then the custom service.
Is it possible to change this order to custom services...
I want to develop for the nRF5340 on the Thingy91X. Are there any good sample projects that allow me to set the target board to Thingy91X/nRF5340/cpuapp?
I only need to...
On nRF54L15 (NCS v3.1.0), we are using the SAADC with ADC_GAIN_1_4 and ADC_REF_INTERNAL at 14-bit resolution to measure an analog voltage on AIN5. The driver sets ref_internal...
i2c_write_read() returns -5 (EIO) immediately when writing register 0x01 to the sensor. Logic analyzer confirms the sensor clock-stretches SCL for ~14µs+ after receiving the...
Hi All,
We have trying the usbd_cdc_acm example program.
It has custom VID and PID. When connected to a windows PC with the correct driver, it is recognised correctly...
Does SDK 3.3 support building hci-lpuart for the Thingy91x yet? I would love to change to that device if it does.
If it does not, are there plans to implement it?
Hi,
I'm running into what looks like a software link-layer issue on the nRF54L15-DK that I'd like a second pair of eyes on. The same firmware works end-to-end with iOS...
Hi,
I’m using GD25WB256 as external flash on nRF9151 for MCUboot secondary slot. It’s currently not available from our supplier, so I’m looking for alternatives.
Current...
Hi everyone,
I am currently facing an issue with the nRF54LM20A where the access port protection is not taking effect after programming SECUREAPPROTECT and APPROTECT into...
