Problem
We have manufactured a custom board using the nRF9151 and we ran into some manufacturing QA/QC issues. The reserved pins of the SiP are very close to ground pads...
Is there any documentation on what peak data rates are available on the nRF9151?
While the Cat-M, Cat-NB1 and Cat-NB2 standard max data rates are easily available, I have...
Hi,
I'm using nRF Connect version 2.9.1 with the buildprog script method of building this project.
I've got some custom boards based on the nRF5340_audio_dk. We swapped...
Hello,
I've seen multiple posts related to this question, but they're not very recent so I wanted to check if there's an updated answer.
Are non-simultaneous multi-image...
I have an Ubuntu Machine where I successfully installed Zephyr SDK and toolchain following instructions given in the official getting started guide here . I was able to compile...
Hello,
I have a custom PCB with the nRF5340 chip. I’m able to flash the board using a J-Link. I’d like to rename the device so that it advertises a specific Bluetooth name...
Hello,*
I'm new to nRF Connect SDK environment, but I'm used to work with Zephyr.
I'm actually confused using west.yml file. I created a new application based on existing...
Hi,
I have the following code running on NRF51822:
int main(void)
{
// Configure GPIO 08 (P1.0) as output.
nrf_gpio_cfg_output(8);
// Set HI on GPIO 08(P1.0...
Greetings,
I'm experimenting with iOS and bluetooth, using the Heart Rate Monitor example. I have tried, and failed, to convert the NSData I get from the "Heart Rate" characteristic...
In one of my current projects, I need:
to have access to more than 8 kB of RAM (which is not possible when using SoftDevice)
to have Observer role (which apparently...
I see many questions regarding developing applications without the SoftDevice. Perhaps I don't understand how this firmware system works, but isnt the SoftDevice required...
I am new to Bluetooth 4.0 and want to use for a specific application. I intend to modify the Bluetooth 4.0 protocol and would need continuous transmission of packets. Is it...
hiii....
i am using lightblue app in i phone to connect with the advertising device...in my ble profyl i have 5 services and 5 characteristics in each... most of dem i...
I make a call to sd_ble_gatts_hvx, and get an error. The call produces an error and I end up in ble_debug_assert_handler
From ble_debug_assert_handler:
The file name is...
Hi,
I've tried to implement s120 softdevice (version 1.0.0 production ready) on NRF51822 Development Kit and run ble_app_multilink_central example from sdk 6.1.0 on it but...
My devices should be able to "see" each other and at the same time they should be able to extract some information from a received Advertising packet. After reading about...
Hi, I use s120 stack. Peripheral device sends a notification 6 in a row, but the central device receives only the first 3 notification. How to get all the notifications?
Hi,
I have 2 pins with PULL_UP in sense mode and when i use sd_power_system_off() i measure 25mA current, which is higher than when my system is on (around 10mA)!!
How...
We are using an nRF8001 with bonding. We are trying to figure out how big the dynamic data is that we need to store (since we are used a fixed-size storage in flash memory...
I just received my Beacon Kit and need a programmer/debugger but money is tight. These are the options I'm looking at:
cut the traces on my nRF51822 EK board and add...
I wrote an application that works using an Enhanced Shockburst-compatible protocol (because I need it so), using the RADIO interface.
What happens if a packet with an address...
