Hello Nordic team,
I am testing a plain CoAP telemetry upload from an nRF54L15 DK over Thread using a Raspberry Pi OTBR and NAT64 to ThingsBoard Cloud.
Hardware / software...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
Hello
We are using nRF5340 as our EVK with a 12 antenna array plate(4x4 with center 4 ones not being there). Our beacon uses nRF52833.
We used Nordic's sample codes- ...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
We are working to add support for the new nRF54 chips using the nRF Connect Bare Metal SDK within our existing mono-repo, which currently supports multiple product generations...
Hi,
Currently we're experiencing some problems to detect events from npm1300 in our custom board but the same issue happens with nrf54l15dk plus npm1300-ek boards when running...
Hi,
We're using the nRF54L15 driven by a 5ppm TCXO connected to the LFCLK. Our application measures the timing external pin events; the accuracy of this measurement is critical...
Hi
I'm having trouble finding two documents: the 'nRF91xx Kits Reduced Receiver Sensitivity Issue.PDF and the related design files for the extra filtering on the nRF91....
Hi everyone,
I believe the object_type should not be of type uint32_t, but of type uint8_t (or maybe nrf_dfu_obj_type_t).
This is the structure I'm talking about inside...
We have been trying to upgrade nRF connect SDK from v3.1.1 to v3.2.1 and run into the following issue: When we enable CONFIG_PM_DEVICE_RUNTIME=y after flashing, the device...
We've encountered an issue when reading OTP memory using tfm_platform_mem_read() .
After invoking tfm_platform_mem_read() , any subsequent call to k_sleep() (or any other...
Looking at this forum post from 11 months ago, and I'm confused about the guidance given. https://devzone.nordicsemi.com/f/nordic-q-a/99083/reading-uicr-value-at-runtime-for...
Hi,
In ncs/v3.1.0/ modules/hal/nordic/nrfx/drivers/include/nrfx_nfct.h, the enum ' nrfx_nfct_param_id_t' is defined as:
In the nrfx support libraries shipped to us with...
We have a board designed with nrf54l15 and we plan to use the RRAM to store the image. That is, no external flash to store images.
For this design, is it possible to use...
Hello,
I am trying to get to grips with the nrfx driver: GRTC.
I want to create the following sequence with the lowest possible power consumption. Activate output 1 for...
Hi
I have two nRF5340 DK boards.
I cannot remember what I last used them for, but I can no longer connect up to them.
In VSCode, when I usually connect to an nRF board...
Hi, I am able to flash my XIAO nrf52840 using my nrf52840dk however the code does not run once flashed. I checked and the code itself is starting at 0x00027000 presumably...
With NCS 3.2.1 I can't make use of custom mbed TLS config headers anymore, the MBEDTLS_CFG_FILE KConfig option always get overwritten. Previously setting CONFIG_CUSTOM_MBEDTLS_CFG_FILE...
Hi,
I tried searching public question on the matter and wasn't able to find anything reminiscent of the problem I have.
I'm developing a presence sensor using ZigBee protocol...
