Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Dear Nordic,
I am debugging a custom hardware with a nRF7002 on-board, using wifi shell app. At this moment the shell does not work as expected, needs to locate where the...
We have two nRF52832-QFAA E0 version devices; Bluetooth works on one, but on the other, it used to work but stopped working over time. Even though we upload the same code...
Hi,
i am working on a project using the nRF54L15.
Hardware: custom board with nRF54L15
Software:
Wirepas SDK (1.6.2)
nrfx drivers (version 3.9.0) with some customization...
Hello
We are using nRF5340 as our EVK with a 12 antenna array plate(4x4 with center 4 ones not being there). Our beacon uses nRF52833.
We used Nordic's sample codes- ...
Hello.
I am currently migrating a project from NCS v3.2.4 to v3.3.1 and transitioning from Partition Manager to devicetree-based partitioning, following the official migration...
Hi,
I am using bare metal SDK v2.0.0 and am trying to build the fuel gauge sample inside nrf-bm\v2.0.0\nrf\samples\pmic\native\npm13xx_fuel_gauge. I am using bm_nrf54l15dk...
I am using nRF54L10 with nRF Connect SDK v3.1. The device connects over BLE, wakes every 30 minutes to read sensor data, and then should enter deep sleep (System OFF). However...
Hello, I am currently experiencing an issue with the 802154_phy_test example on the nRF54L15-DK board, and I would appreciate your technical support.
[ Environment ]
...
We are experiencing an issue with the QSPI driver on nRF54L15 where external flash access stops working after a BLE bonding procedure.
The system works correctly until bonding...
Hello
I am developpping a product with composite USB (CDC_ACM & HID) and Bluetooth Low Energy, based on a nRF52840 chip.
Can Nordic provides PID free to use for small...
Dear support,
We are connecting with an MQTT server with an expired server certificate. My expectation is that the handshake fails, but apparently the NRF9161 accepts the...
Hello, we are having issues with using the nrf9151DK as a programmer for our own custom nrf9151 board. As the board seems to be locked, we tried to unlock it using the nrfutil...
Hi,
looking through many Posts regarding this topic, i recognized the wiring and labels of the nRF52 DK has changed.
GND is explicitly on the P20 Header anymore.
-nRF52...
Hi everyone,
I'm working on a project using the nRF54 and Zephyr RTOS . Previously, I implemented almost identical functionality on an nRF52, where the device consumed around...
