Hello,
i would like to know if the new SoftDevice 130 for the nrf51822 is compatible with the DFU OTA bootloader example provided in the SDK (nrf51822/Board/nrf6310/device_firmware_updates...
Can I get uuid of central device from peripheral device(nrf51822) ?
I want to check out which smart device is connected.
May be I can tell central is iphone4s or iphone5...
Recently s110_nrf51822_7.0.0 softdevice has been released. I cannot find specification where those new amazing features (they are impressive, indeed :) ) are described, so...
Hi All,
Please correct the following in my understanding. Also , i am planning to build a
remote controlled device using a PWM output. How does ATT,GATT and GAP affect/influence...
My board works most of the time are very good，but one time i power down the board when ble connecting and data transmitting，the board can't work when power on.and i can't...
Hello,
Our company has developed hardware using the nRF52840. We are using nRF Connect SDK 3.2.1. We have a developer that has been working on creating a mobile app using...
Hi Nordic,
I am currently evaluating the nRF9151 SMA Development Kit for a Non-Terrestrial Network (NTN) project and would like to inquire about the available NTN-enabled...
Hi
I have read that the J-Link OB on nRF DK's can program nRF's other generations that the one on the DK itself by using the J-Tag output connector. But does the J-link...
I want to pass a variable to my program so I'm using the command: west build -b nrf52840dk_nrf52840 -p --build-dir build -- -Dmy_variable=40 Then in my program I want to print...
I'm having some issues creating multiple LittleFS file systems on a project. This is part of a larger project, so I used the Zephyr LittleFS test code to create a demonstration...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
Trying to work thru the dev academy exercise 2 using v3.2.4 SDK. I presume this should work because the readme says must be greater than v2.8.0 for thingy91.
I made all...
We are using the legacy 17.1 nrf sdk with the nrf52840 MCU in tickless idle mode and notice that after about 10.5 minutes the current draw jumps from ~90uA to ~277 uA.
There...
Hi,
We are working with the nRF54L15 using nRF Connect SDK v2.8.0 and would like to enable the secure boot feature.
However, it appears that the SMP Server sample in...
I'm using put all together 2 sample
a) NUS Uart that is used for the configuration;
b) zephyr/samples/net/opentread/coap Using the nrf5340dk/nrf5340/cpuapp.
The compilation...
Hello,
Step 5.2 of this part of the course has a code example which shows which i2c node to use to control the temperature sensor. In the case of the nRF54l15DK it is...
Hello Nordic team,
We are using an nRF5340 as the host processor, and an nRF9160 module is mounted on top of it. All LTE modem AT commands are sent from nRF5340 to nRF9160...
I'm trying to implement the NRF5340 as an I2C slave. The current answers all show the answer as old to look for a newer answer. Were implementing the NRF5340 as a slave to...
Dear all,
is it planned to update the declaration of conformity of nRF9160 from EN 301 908-13 V13.2.1 to EN 301 908-13 V13.3.1?
EN 301 908-13 V13.2.1 is only valid until...
I am currently working with the Aliro 1.0.0 from nRF Door Lock and Access Control Add-on.
I need to know how to properly configure or set custom data fields for Aliro protocol...
