Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Although the recommended circuit in the datasheet shows a 0402-size inductor, I have not been able to find any 0402 inductors that meet the required specifications.
Could...
Hi there,
We have been working on nRF9151DK (dev kits) containing the mfw_nrf91x1_2.0.1 modem firmware. Now we have some custom prototype boards ready (same SiP obviously...
I understand how to update the 9151 via LTE on the nrfCloud and now I want to update the 5340 via the same method.
I'm starting to understand the SMP Server example which...
Hi everyone, I’m looking into using LTE-M with nRF9151, and in that context I’m considering using an eSIM. I’d like to ask a few general questions around this topic:
1....
Hi,
i'm using nRF52832 to construct an BTHomev2 sensor.
In development, we find the firmware seems to randomly fail in k_sleep(), but once we full earse the chip before...
I am trying to configure Analogin_rev pin as ADC pin and I did the code changes, but I am getting the error -22 while trying to Configure ADC channel. Here is the snippet...
Dear Nordic Specialist,
I am using two nRF5340 DKs running the Direction Finding connection-based Central/Peripheral examples, and I would like to evaluate the maximum achievable...
Hi
What is the nRF5340 PDM frequency max and min can be set?
Because below is our microphone frequency spec., we want to set PDM frequency into like between 450~850KHz...
Hello, I’m trying to understand the background of the issue described in nRF9151 DK v0.9.0 Errata . Could someone explain what caused it and, if possible, give an idea of...
Hi
I am trying to integrate a "TMP117" temperature sensor with an nRF54L15 using the existing Zephyr tmp11x sensor driver. The device is detected and initialized correctly...
Hi There,
We are currently developing a prototype using the mRF5340. (MDBT53-1M ) The key is to operate I2S at 192kHz.
Please let me confirm the following:
Is LRCK's...
Hello,
In previous NCS versions I know I have heard the test tone triggered by button 4 on Audio DK work out of the box.
I am currently experimenting with NCS v3.2.1/0...
Hi dear forum members,
I’m working on a firmware project for the NRF52840 that utilizes BLE, DFU, I2C, WDT, some cryptographic libraries, and a few sensor libraries. However...
Hey, wanted to know a few things regarding npm1300 1. Can it handle short circuit of it's buck/LDO outputs? Or we need to have some sort of protection for each buck. 2. If...
Hello,
I am using an nRF54LM20DK with nRF Connect SDK v3.1.1 and I am unable to establish I2C communication with an external DPS368 sensor.
The application starts correctly...
